Flywheel - Install
Show/hide table
| Alat yang Diperlukan | |||
| Alat | Nomor Suku Cadang | Keterangan Suku Cadang | Jml |
| A | 138-7574 | Bracket Sambungan | 1 |
| B | FT2712 | Stud Pemandu | 1 |
| C | - | Loctite 242 | 1 |
- Tingkatkan temperatur roda-gigi ring. Posisikan roda-gigi ring dengan nomor suku cadang menghadap ke arah crankshaft. Pasang roda-gigi ring pada flywheel. Biarkan roda-gigi ring mendingin. Gunakan hammer lunak untuk memasang roda-gigi ring pada bahu flywheel.
Show/hide table
Ilustrasi 1 g01132214 - Pasang Peralatan (A) dan peralatan pengangkat yang sesuai pada flywheel (2). Flywheel (2) memiliki berat sekitar
79 kg (175 lb) . - Posisikan flywheel (2) pada Peralatan (B).
- Gunakan Peralatan (C) pada baut (1).
- Pasang baut (1). Lepaskan Alat (B). Pasang baut lainnya (1). Kencangkan baut secara merata dengan torsi pengencangan
300 ± 40 N·m (221 ± 30 lb ft) . - Periksa runout flywheel. Rujuk ke Pengujian dan Penyetelan, "Flywheel - Pemeriksaan" untuk prosedur yang benar.
Show/hide table
 |
|
Selalu gunakan sarung tangan pelindung saat menangani suku cadang yang telah dipanaskan. |
Caterpillar Information System:
C11 and C13 Engines for Caterpillar Built Machines Flywheel - Remove
C11 and C13 Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
2005/01/31 Different Wire Removal Tool and Different Wire Installation Tool Are Required for 85 Pin Connectors on Engine Wiring Harnesses {0709}
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Install
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Assemble
325D and 329D Excavators Machine Security System - If Equipped
3500 Engines Coolant Level Sensor - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Finding Top Center Position for No. 1 Piston
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Disassemble
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Remove
2004/12/01 A New PEEC Transducer Module is now Used {1917}
3508B, 3512B and 3516B Generator Set Engines Housing (Front) - Install
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Troubleshooting Faults With Service Codes
C11 and C13 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove
C11 and C13 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install
C11 and C13 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
345C Excavator Hydraulic System Main Hydraulic Pump Air - Purge
2005/03/07 Wireless Communication Adapter Allows Radio Frequency Communication Between Computer and Electronic Control Module {0785, 0788}
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Control Module
C32 Marine Engines Coolant Level Sensor Circuit - Test
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Control Panel (Air Conditioner and Heater)
390F MHPU Mobile Hydraulic Power Unit Fuel System Water Separator - Drain
345 MHPUC Mobile Hydraulic Power Unit Hydraulic System Swing Motor - Test - Measurement of Case Drain Oil
2004/12/01 An Improved Valve in the Bowl of the Fuel/Water Separator is Available {1261, 1263}