Flywheel Housing - Remove and Install
Dimulai dengan:
- Lepaskan motor starter elektrik. Rujuk ke Pembongkaran dan Perakitan, "Motor Starter Elektrik - Pelepasan dan Pemasangan".
- Lepaskan flywheel. Rujuk ke Pembongkaran dan Perakitan, "Flywheel - Pelepasan".
- Penopang engine.
Show/hide table
Ilustrasi 1 g01132273 - Pasang peralatan pengangkat yang sesuai pada rumah flywheel (2). Rumah flywheel (2) memiliki berat sekitar
62 kg (137 lb) . - Lepaskan baut (1) dan rumah flywheel (2).
Show/hide table
| Alat yang Diperlukan | |||
| Alat | Nomor Suku Cadang | Keterangan Suku Cadang | Jml |
| A | 1U-8846 | Seal Gasket | 1 |
- Gunakan Peralatan (A) pada bagian muka blok silinder.
Show/hide table
Ilustrasi 2 g01132273 - Pasang peralatan pengangkat yang sesuai pada rumah flywheel (2). Rumah flywheel (2) memiliki berat sekitar
62 kg (137 lb) . Posisikan rumah flywheel (2) pada bagian belakang blok silinder. - Pasang baut (1).
Diakhiri dengan:
- Pasang flywheel. Rujuk ke Pembongkaran dan Perakitan, "Flywheel - Pemasangan".
- Pasang motor starter elektrik. Rujuk ke Pembongkaran dan Perakitan, "Motor Starter Elektrik - Pelepasan dan Pemasangan".
Caterpillar Information System:
C11 and C13 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install
C11 and C13 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Troubleshooting Faults With Service Codes
C11 and C13 Engines for Caterpillar Built Machines Flywheel - Install
C11 and C13 Engines for Caterpillar Built Machines Flywheel - Remove
C11 and C13 Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
2005/01/31 Different Wire Removal Tool and Different Wire Installation Tool Are Required for 85 Pin Connectors on Engine Wiring Harnesses {0709}
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Install
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Assemble
325D and 329D Excavators Machine Security System - If Equipped
3500 Engines Coolant Level Sensor - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Finding Top Center Position for No. 1 Piston
345C Excavator Hydraulic System Main Hydraulic Pump Air - Purge
2005/03/07 Wireless Communication Adapter Allows Radio Frequency Communication Between Computer and Electronic Control Module {0785, 0788}
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Control Module
C32 Marine Engines Coolant Level Sensor Circuit - Test
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Control Panel (Air Conditioner and Heater)
390F MHPU Mobile Hydraulic Power Unit Fuel System Water Separator - Drain
345 MHPUC Mobile Hydraulic Power Unit Hydraulic System Swing Motor - Test - Measurement of Case Drain Oil
2004/12/01 An Improved Valve in the Bowl of the Fuel/Water Separator is Available {1261, 1263}
C11 and C13 Engines for Caterpillar Built Machines Fuel Filter Base - Remove and Install
3508B, 3512B and 3516B Generator Set Engines Accessory Drive (Front) - Remove - Engine Oil Pump and Water Pump
3508B, 3512B and 3516B Generator Set Engines Accessory Drive (Front) - Install - Engine Oil Pump and Water Pump
3508C, 3512C and 3516C Marine Engines Accessory Drive (Front) - Disassemble - Engine Oil Pump and Water Pump