Coolant Level Sensor - Remove and Install
Show/hide table
| 注意 |
|---|
|
在检查、保养、测试、调整及维修产品时，请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前，请准备好盛接液体用的适当容器。 |
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 将冷却系统中的冷却液排入适当的容器至液位低于冷却液液位传感器，以便保存或废弃。
Show/hide table
图 1 g01132110 - 断开线束组件，然后拆下冷却液液位传感器 ( 1)。
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 安装冷却液液位传感器 ( 1) 并拧紧至扭矩为
30 ± 5 N·m (22 ± 4 lb ft) 。注: 不要将额外的密封胶涂抹到冷却液液位传感器的螺纹上。
- 连接线束组件。
- 加注冷却系统。 请参考操作与保养 , "冷却系统冷却液 - 更换"。
Show/hide table
| |
| 图 2 | g01132110 |
Caterpillar Information System:
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Finding Top Center Position for No. 1 Piston
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Disassemble
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Remove
2004/12/01 A New PEEC Transducer Module is now Used {1917}
3508B, 3512B and 3516B Generator Set Engines Housing (Front) - Install
C11 and C13 Engines for Caterpillar Built Machines Engine Oil Cooler - Install
C11 and C13 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove
C11 and C13 Engines for Caterpillar Built Machines Engine Oil Filter Base - Install
C11 and C13 Engines for Caterpillar Built Machines Engine Oil Filter Base - Remove
3508B, 3512B and 3516B Generator Set Engines Housing (Front) - Remove
C11 and C13 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Turbocharger - Install
325D and 329D Excavators Machine Security System - If Equipped
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Assemble
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Install
2005/01/31 Different Wire Removal Tool and Different Wire Installation Tool Are Required for 85 Pin Connectors on Engine Wiring Harnesses {0709}
C11 and C13 Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Flywheel - Remove
C11 and C13 Engines for Caterpillar Built Machines Flywheel - Install
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Troubleshooting Faults With Service Codes
C11 and C13 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove
C11 and C13 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install
C11 and C13 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
345C Excavator Hydraulic System Main Hydraulic Pump Air - Purge