Sensors and Electrical Connectors
Show/hide table
| Connector | Function |
|---|---|
| J1/P1 | ECM connector (70−pin) |
| J2/P2 | ECM connector (70−pin) |
| J61/P61 | Customer connector (40-pin) |
| J63 | Engine service tool connector |
| J66 | Customer supplied service tool connector |
| J100/P100 | Engine coolant temperature sensor |
| J101/P101 | Engine oil temperature sensor |
| J103/P103 | Intake manifold air temperature sensor |
| J142/P142 | Auxiliary temperature sensor |
| J200/P200 | Boost pressure sensor |
| J201/P201 | Engine oil pressure sensor |
| J203/P203 | Atmospheric pressure sensor |
| J204/P204 | Injection actuation pressure sensor |
| J209/P209 | Fuel pressure sensor |
| J220/P220 | Auxiliary pressure sensor |
| J300/P300 | Injector solenoid harness |
| P400 | Engine timing calibration |
| J401/P401 | Primary engine speed/timing sensor |
| J402/P402 | Secondary engine speed/timing sensor |
| J403/P403 | Throttle position sensor |
| J500/P500 | Injection actuation pressure control valve |
| J800/P800 | Engine coolant level switch |
Show/hide table
 | |
| Illustration 1 | g01123879 |
Components for the 3126B engine | |
Show/hide table
 | |
| Illustration 2 | g01125074 |
Sensor locations (1) Engine coolant temperature sensor (2) Injection actuation pressure sensor (3) Boost pressure sensor (4) Intake manifold air temperature sensor (5) Engine oil temperature sensor (6) Atmospheric pressure sensor (7) Primary engine speed/timing sensor (8) Secondary engine speed/timing sensor (9) Injection actuation pressure control valve (10) Fuel pressure sensor (11) Engine oil pressure sensor (12) Timing calibration port (13) Electronic Control Module (ECM) (14) J2 ECM connector (15) Timing calibration probe connector (16) J1 ECM connector | |
Caterpillar Information System:
C27 and C32 Engines Rear Gear Group - Time
3508B, 3512B and 3516B Generator Set Engines Crankshaft - Install
3508B, 3512B and 3516B Generator Set Engines Crankshaft - Remove
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel System Secondary Filter - Replace
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel System - Prime
3508B, 3512B and 3516B Generator Set Engines Engine Oil Pan - Install
3508B, 3512B and 3516B Generator Set Engines Engine Oil Pan - Remove
C32 Marine Engines Fuel System
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Water Pump - Inspect
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Turbocharger - Inspect - If Equipped
2004/12/01 Improved Alignment of a Coolant Tube {1380}
C9 Industrial Engines Cooling System
3126B Petroleum Engine Cooling System
Installation of 244-1090 Alarm Gp {7400, 7402, 7407} Installation of 244-1090 Alarm Gp {7400, 7402, 7407}
3500 and 3500B Engines Refill Capacities and Recommendations
C27 and C32 Engines Water Pump - Test
3500B High Displacement Generator Set Engines Alternator and Fan Belts - Inspect/Adjust/Replace
C7 On-Highway Engine Engine Oil Filter Base and Oil Cooler - Remove
345C MHPU Mobile Hydraulic Power Unit Hydraulic System Relief Valve (Swing)
2004/12/01 New Ignition Transformers are Used {1561}
C27 and C32 Engines Fuel System Pressure - Test
3500B and 3500 Marine Propulsion Engines with EUI Option Product Lifting
3500B and 3500 Marine Propulsion Engines with EUI Option Product Storage
3500B and 3500 Marine Propulsion Engines with EUI Option Refill Capacities and Recommendations