Engine Oil Pan - Remove
拆卸步骤
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将发动机机油排入合适的容器以便保存或废弃。
- 拆下将机油泵接头固定到发动机油底壳 (2) 的螺栓 (1) 。
Show/hide table
图 1 | g01123595 |
- 拆下将发动机油底壳 (2) 连接到缸体的螺栓 (3) 。
Show/hide table
图 2 | g01123597 |
- 将适当起吊设备连在发动机吊耳上。
- 3508B 发动机的重量约为 4445 kg (9800 lb)。 油底壳的重量约为 240 kg (530 lb)。
- 3512B 发动机的重量约为 5900 kg (13000 lb)。 油底壳的重量约为 295 kg (650 lb)。
- 3516B 发动机的重量约为 7711 kg (17000 lb)。 油底壳的重量约为 409 kg (900 lb)。
- 3508B 发动机的重量约为 4445 kg (9800 lb)。 油底壳的重量约为 240 kg (530 lb)。
Show/hide table
不适当的吊具会使被吊装设备翻倒,造成伤害和损坏。 |
Show/hide table
图 3 | g01123599 |
- 从油底壳提升发动机。
- 将油底壳密封垫 (4) 从发动机油底壳上拆下。 拆下 O 形密封圈 (5) 。 拆下螺栓 (6) 。 从发动机油底壳上卸下法兰 (7) 。 将密封件 (8) 从法兰上拆下。
Show/hide table
图 4 | g01123600 |
Caterpillar Information System:
C32 Marine Engines Fuel System
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Water Pump - Inspect
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Turbocharger - Inspect - If Equipped
2004/12/01 Improved Alignment of a Coolant Tube {1380}
C9 Industrial Engines Cooling System
C27 and C32 Engines Finding Top Center Position for No. 1 Piston
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Crankcase Breather - Replace
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Alternator and Fan Belts - Replace
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Alternator and Fan Belts - Inspect/Adjust
C7 Engines for Caterpillar Built Machines Fuel Transfer Pump - Install
C7 Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove
345C Excavator Hydraulic System Stick Drift Reduction Valve
3508B, 3512B and 3516B Generator Set Engines Engine Oil Pan - Install
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel System - Prime
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel System Secondary Filter - Replace
3508B, 3512B and 3516B Generator Set Engines Crankshaft - Remove
3508B, 3512B and 3516B Generator Set Engines Crankshaft - Install
C27 and C32 Engines Rear Gear Group - Time
3126B Petroleum Engine Sensors and Electrical Connectors
3126B Petroleum Engine Cooling System
Installation of 244-1090 Alarm Gp {7400, 7402, 7407} Installation of 244-1090 Alarm Gp {7400, 7402, 7407}
3500 and 3500B Engines Refill Capacities and Recommendations
C27 and C32 Engines Water Pump - Test
3500B High Displacement Generator Set Engines Alternator and Fan Belts - Inspect/Adjust/Replace