Engine Oil Pan - Install
安装步骤
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件描述 | 数量 |
| A | - | Loctite 595 | - |
| B | 1P-0808 | 多功能润滑脂 | - |
| C | - | 导向螺柱 （3/8 - 16 x 5 in） |
4 |
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 清洁发动机油底壳和缸体的密封表面。
- 将工具 (A) 涂敷在油底壳密封垫 (4) 上。 将油底壳密封垫安装到发动机油底壳上。 将工具 (C) 安装在发动机油底壳内。
Show/hide table
 | |
| 图 1 | g01123600 |
- 将工具 (B) 涂抹在法兰 (7) 的孔上。 将密封件 (8) 安装在法兰 (7) 内。 定位法兰并安装螺栓 (6) 。 将 O 形密封圈 (5) 安装在法兰上。
- 将适当起吊设备连在发动机吊耳上。
- 3508B 发动机的重量约为 4445 kg (9800 lb)。 油底壳的重量约为 240 kg (530 lb)。
- 3512B 发动机的重量约为 5900 kg (13000 lb)。 油底壳的重量约为 295 kg (650 lb)。
- 3516B 发动机的重量约为 7711 kg (17000 lb)。 油底壳的重量约为 409 kg (900 lb)。
- 3508B 发动机的重量约为 4445 kg (9800 lb)。 油底壳的重量约为 240 kg (530 lb)。
Show/hide table
 |
不适当的吊具会使被吊装设备翻倒，造成伤害和损坏。 |
Show/hide table
 | |
| 图 2 | g01123599 |
- 提升发动机。 将发动机置于发动机油底壳上。
- 安装螺栓 (3) 。 将工具 (C) 从发动机油底壳 (2) 上拆下，然后安装剩余的螺栓 (3) 。
Show/hide table
 | |
| 图 3 | g01123597 |
- 安装将机油泵的接头固定到发动机油底壳 (2) 的螺栓 (1) 。
Show/hide table
 | |
| 图 4 | g01123595 |
- 加注发动机油底壳至发动机油尺上显示的正确油位。 有关正确的程序以及发动机机油的使用，请参阅操作和保养手册。
Caterpillar Information System:
3508B, 3512B and 3516B Generator Set Engines Engine Oil Pan - Remove
C32 Marine Engines Fuel System
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Water Pump - Inspect
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Turbocharger - Inspect - If Equipped
2004/12/01 Improved Alignment of a Coolant Tube {1380}
C9 Industrial Engines Cooling System
C27 and C32 Engines Finding Top Center Position for No. 1 Piston
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Crankcase Breather - Replace
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Alternator and Fan Belts - Replace
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Alternator and Fan Belts - Inspect/Adjust
C7 Engines for Caterpillar Built Machines Fuel Transfer Pump - Install
C7 Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel System - Prime
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel System Secondary Filter - Replace
3508B, 3512B and 3516B Generator Set Engines Crankshaft - Remove
3508B, 3512B and 3516B Generator Set Engines Crankshaft - Install
C27 and C32 Engines Rear Gear Group - Time
3126B Petroleum Engine Sensors and Electrical Connectors
3126B Petroleum Engine Cooling System
Installation of 244-1090 Alarm Gp {7400, 7402, 7407} Installation of 244-1090 Alarm Gp {7400, 7402, 7407}
3500 and 3500B Engines Refill Capacities and Recommendations
C27 and C32 Engines Water Pump - Test
3500B High Displacement Generator Set Engines Alternator and Fan Belts - Inspect/Adjust/Replace
C7 On-Highway Engine Engine Oil Filter Base and Oil Cooler - Remove