Crankshaft - Remove
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 4C-9832     | 发动机翻转支架     | 1     |
B     | 138-7576     | 连杆支架     | 2     |
开始:
- 拆卸摇臂轴组件和推杆。 请参阅拆解和组装, "摇臂轴和推杆 - 拆卸"。
- 拆下飞轮壳体。 请参阅拆解和组装, "飞轮壳体 - 拆卸和安装"。
- 拆卸前壳体。 请参阅拆解和组装, "前驱动壳体 - 拆卸和安装"。
- 卸下活塞冷却喷嘴。 请参阅拆解和组装, "活塞冷却喷嘴 - 拆卸和安装"。
Show/hide table
注意 |
---|
当活塞和连杆被推离轴箱时,没有拆卸摇臂轴组件和推杆可能会损坏气门。 为避免损坏气门,拆卸曲轴前拆卸摇臂轴组件和推杆。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用工具 (A) 将发动机转到水平位置。 发动机可用工具 (A) 或挡块支撑。
- 3508B 发动机的重量约为 3470 kg (7650 lb)。
- 3512B 发动机的重量约为 5440 kg (12000 lb)。
- 3516B 发动机的重量约为 6550 kg (14440 lb)。
- 3508B 发动机的重量约为 3470 kg (7650 lb)。
- 在配重 (2) 上贴上标记。 从曲轴上拆下螺栓 (1) 和配重 (2) 。
注: 切勿重复使用螺栓 (1) 。 用新的螺栓将配重固定到曲轴。
注: 如果从发动机上拆卸活塞和连杆组件,则没必要从曲轴上拆卸配重。
Show/hide table
图 1 | g01124519 |
- 拆下螺栓 (3) 。 拆卸连杆轴承盖 (4) 并将连杆从曲轴上推出。
注: 确保曲轴上的轴径没有被连杆擦伤。
Show/hide table
图 2 | g01124522 |
注: 对连杆轴承盖和连杆进行编号,以便安装。
- 在曲轴 (7) 的每一端都连上工具 (B) 。 将适当的起吊设备连接在工具 (B) 上。 曲轴 3508B 的重量约为 398 kg (877 lb)。 曲轴 3512B 的重量约为 590 kg (1300 lb)。 曲轴 3516B 的重量约为 800 kg (1764 lb)。
Show/hide table
图 3 | g01124538 |
- 拆下螺栓 (5) 和主轴承盖 (6) 。
- 从中心主轴承两侧卸下止推盘 (8) 。
- 将曲轴 (7) 从缸体上拆下。
- 将主轴承上轴瓦从缸体上拆下。
- 从连杆上拆下连杆轴承上轴瓦。
- 如有必要,从曲轴的每一端拆卸螺栓 (9) 和曲轴齿轮 (10) 。
Show/hide table
图 4 | g01124543 |
Caterpillar Information System:
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel System Secondary Filter - Replace
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel System - Prime
3508B, 3512B and 3516B Generator Set Engines Engine Oil Pan - Install
3508B, 3512B and 3516B Generator Set Engines Engine Oil Pan - Remove
C32 Marine Engines Fuel System
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Water Pump - Inspect
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Turbocharger - Inspect - If Equipped
2004/12/01 Improved Alignment of a Coolant Tube {1380}
C9 Industrial Engines Cooling System
C27 and C32 Engines Finding Top Center Position for No. 1 Piston
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Crankcase Breather - Replace
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Alternator and Fan Belts - Replace
3508B, 3512B and 3516B Generator Set Engines Crankshaft - Install
C27 and C32 Engines Rear Gear Group - Time
3126B Petroleum Engine Sensors and Electrical Connectors
3126B Petroleum Engine Cooling System
Installation of 244-1090 Alarm Gp {7400, 7402, 7407} Installation of 244-1090 Alarm Gp {7400, 7402, 7407}
3500 and 3500B Engines Refill Capacities and Recommendations
C27 and C32 Engines Water Pump - Test
3500B High Displacement Generator Set Engines Alternator and Fan Belts - Inspect/Adjust/Replace
C7 On-Highway Engine Engine Oil Filter Base and Oil Cooler - Remove
345C MHPU Mobile Hydraulic Power Unit Hydraulic System Relief Valve (Swing)
2004/12/01 New Ignition Transformers are Used {1561}
C27 and C32 Engines Fuel System Pressure - Test