Fuel Transfer Pump - Install
安装步骤
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件说明 | 数量 |
| A | 218-8171 | 螺栓 | 1 |
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将燃油输油泵 (2) 安置在单体喷油器液压泵上。 确保将燃油输油泵的驱动舌片对准泵轴端部的驱动槽。
Show/hide table
 | |
| 图 1 | g01123057 |
- 安装拉紧螺栓 (4) 。 拧紧螺栓，形成滑动配合。
- 拆卸位于左上孔的工具 (A) 并安装其余拉紧螺栓 (1) 以形成滑动配合。
- 安装燃油输油泵 (2) 的螺栓 (3) 。 拧紧螺栓，形成滑动配合。
- 从单体喷油器液压泵的左下角开始，按交叉顺序拧紧螺栓 (4) 至扭矩为 28 ± 2 N·m (21 ± 1 lb ft)。 再次拧紧螺栓。
- 拧紧螺栓 (3) ，使其扭矩达到 8.0 ± 0.4 N·m (71 ± 4 lb in)。
End By: 安装单体喷油器液压泵。 请参阅 拆解和组装, "单体喷油器液压泵 - 安装"。
Caterpillar Information System:
C7 Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove
345C Excavator Hydraulic System Stick Drift Reduction Valve
2004/11/01 New Injectors and New Flash Files are Now in Production {1290, 7620}
C9 Marine Engines and C9 Marine Generator Sets Cylinder Block Cover Group
SR4 and SR4B Generators and Control Panels Maintenance Interval Schedule - Standby
SR4 and SR4B Generators and Control Panels Maintenance Interval Schedule - Standard
325D and 329D Excavators Engine Starting with Auxiliary Start Receptacle - If Equipped
C32 Marine and Marine Generator Set Engines Cooling System
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Refill Capacities and Recommendations
C32 Marine and Marine Generator Set Engines Air Inlet and Exhaust System
2004/11/01 New Software for Machine Information Display System (MIDS) {7620}
UPS 120, UPS 150, UPS 250 and UPS 300 Uninterruptible Power Supplies Software Installation
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Alternator and Fan Belts - Inspect/Adjust
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Alternator and Fan Belts - Replace
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Crankcase Breather - Replace
C27 and C32 Engines Finding Top Center Position for No. 1 Piston
C9 Industrial Engines Cooling System
2004/12/01 Improved Alignment of a Coolant Tube {1380}
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Turbocharger - Inspect - If Equipped
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Water Pump - Inspect
C32 Marine Engines Fuel System
3508B, 3512B and 3516B Generator Set Engines Engine Oil Pan - Remove
3508B, 3512B and 3516B Generator Set Engines Engine Oil Pan - Install
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel System - Prime