Bulldozer - Install
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 5P-6215     | Jack Stands     | 2     |
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- Position Tooling (A) under push arms (6). The center of the bearings is 54.6 cm (21.50 inches) from the ground (X) .
Show/hide table
Illustration 1 | g00727223 |
Show/hide table
Illustration 2 | g00727207 |
- Install the push arms and the trunnions in the bearings.
- Install caps (5) .
- Connect tilt cylinder hose assemblies (1) to the elbows.
Show/hide table
Illustration 3 | g00727204 |
- Fasten a hoist to the rod end of the lift cylinders. Support the weight of the cylinders with the hoist.
Show/hide table
Illustration 4 | g00727206 |
- Extend the lift cylinders until rod assemblies (2) are in position on the trunnion balls on the bulldozer blade.
Note: Install an equal amount of shims on each side of caps (3) in order to obtain 0.3 mm (.010 inch) to 0.8 mm (.030 inch) clearance between the cap and the bulldozer trunnion ball.
- Put the shims and caps (3) into position on rod assemblies (2) and install bolts (4) and the nuts.
- Fill the implement hydraulic system. Refer to the appropriate Operation and Maintenance Manual for the correct procedure.
Caterpillar Information System:
D6M Track-Type Tractor Machine Systems Bulldozer - Disassemble
D6M Track-Type Tractor Machine Systems Bulldozer - Assemble
D6M Track-Type Tractor Machine Systems Bulldozer (VPAT) - Remove
D6M Track-Type Tractor Machine Systems Bulldozer (VPAT) - Install
545 Wheel Skidder Fuel System Secondary Filter - Replace
D6M Track-Type Tractor Machine Systems Battery - Remove and Install
D6M Track-Type Tractor Machine Systems Air Conditioner and Heater Fan Motor - Remove and Install
D6M Track-Type Tractor Machine Systems Air Conditioner Dryer - Remove and Install
515 Wheel Skidder and 525 Wheel Skidder Steering Control
637E Series II Wheel Tractor-Scrapers Cushion-Hitch Control
515 Wheel Skidder and 525 Wheel Skidder Window Wiper and Washer Control
623F Wheel Tractor-Scraper Power Train Transmission Electronic Control System
D6M Track-Type Tractor Machine Systems Bulldozer - Remove
D6M Track-Type Tractor Machine Systems Bulldozer Angle Cylinder - Install
D6M Track-Type Tractor Machine Systems Bulldozer Angle Cylinder - Remove
D6M Track-Type Tractor Machine Systems Bulldozer C-Frame - Remove and Install
D6M Track-Type Tractor Machine Systems Bulldozer Control Valve - Assemble
D6M Track-Type Tractor Machine Systems Bulldozer Control Valve - Disassemble
D6M Track-Type Tractor Machine Systems Bulldozer Control Valve - Install
D6M Track-Type Tractor Machine Systems Bulldozer Control Valve - Remove
D6M Track-Type Tractor Machine Systems Bulldozer Lift Cylinder - Install
D6M Track-Type Tractor Machine Systems Bulldozer Lift Cylinder - Remove
D6M Track-Type Tractor Machine Systems Bulldozer Lift Cylinder Mounts - Remove and Install
D6M Track-Type Tractor Machine Systems Bulldozer Tilt Cylinder - Install