WIRING DIAGRAM FOR INSTALLING THE MARINE POWER DISPLAY Caterpillar

WIRING DIAGRAM FOR INSTALLING THE MARINE POWER DISPLAY

Usage:

WIRING DIAGRAM FOR INSTALLING THE MARINE POWER DISPLAY

CONFIDENTIAL TIBU3680-00

Show/hide table

TECHNICAL INFORMATION BULLETIN	AUGUST 21, 2002
ENGINES	ALL ELECTRONIC MARINE ENGINES EQUIPPED WITH MARINE POWER DISPLAY
	Component Code 7450

SUBJECT: CONNECTIONS FOR THE MARINE POWER DISPLAY

PROBLEM:

In the Service Manual, SENR5002-03, Installation Guide For Marine Engine Electronic Displays, Illustration 38 is not correct. The wiring for the Alarm Relay is shown incorrectly. Illustration 38 shows the connections for the Marine Power Display.

SOLUTION:

The corrected Illustration 38 follows. The correct illustration will be included in the next revision of the service manual.

Illustration 38
Connect pin 1 to pin 3 for STBD display. Connect pin 1 and pin 2 to pin 3 for center display. Connect pin 2 to pin 3 for PORT display.

COPYRIGHT 2002 CATERPILLAR
ALL RIGHTS RESERVED

Caterpillar Information System:

Caterpillar is releasing replacement software for PCS version 2.07A and 2.07AR software (Cat p/n 213-8794 and 213-8799 respectively) Caterpillar is releasing replacement software for PCS version 2.07A and 2.07AR software (Cat p/n 213-8794 and 213-8799 respectively)

CASE DRAIN RETURN SCREEN ON D11R AND D11R CARRYDOZER HYDRAULIC TANK MUST BE CHECKED CASE DRAIN RETURN SCREEN ON D11R AND D11R CARRYDOZER HYDRAULIC TANK MUST BE CHECKED

Cracks have been found in the radome of the 167-8930 GPS Antenna and the 194-8015 GPS Antenna Cracks have been found in the radome of the 167-8930 GPS Antenna and the 194-8015 GPS Antenna

Temporary Change to the PS41004 Hood Skin Repair Procedure for D9R Track-Type Tractors Temporary Change to the PS41004 Hood Skin Repair Procedure for D9R Track-Type Tractors

PREVENTING CRACKS IN THE REAR TRACK ROLLER FRAME PREVENTING CRACKS IN THE REAR TRACK ROLLER FRAME

The Pins for the Sidebar Bend or Break The Pins for the Sidebar Bend or Break

USE THE 2P-4005 ENGINE OIL FILTER ASSEMBLY TO REPLACE 1R-0716 ENGINE OIL FILTER ASSEMBLY USE THE 2P-4005 ENGINE OIL FILTER ASSEMBLY TO REPLACE 1R-0716 ENGINE OIL FILTER ASSEMBLY

Early Detection Can Prevent Crack Growth into A-Pin Bore Early Detection Can Prevent Crack Growth into A-Pin Bore

Incorrect Speed Sensor Wiring Causes Fill Calibration to Abort Incorrect Speed Sensor Wiring Causes Fill Calibration to Abort

Acceleration or Deceleration Switch May Stick on 185-1106 or 208-6100 Handles Used on the Transmission/Steering Joystick Acceleration or Deceleration Switch May Stick on 185-1106 or 208-6100 Handles Used on the Transmission/Steering Joystick

Installation and Replacement Procedure for Greased Linkage Pin Joints on 992G Wheel Loaders Installation and Replacement Procedure for Greased Linkage Pin Joints on 992G Wheel Loaders

REPLACEMENT OF THE HEATER MOTOR AND BLOWER WHEEL REPLACEMENT OF THE HEATER MOTOR AND BLOWER WHEEL

Tilt Cylinder Dump Noise Tilt Cylinder Dump Noise

Power Train Oil Filter Bypass Alarm Activates at a Lower Pressure than Intended Power Train Oil Filter Bypass Alarm Activates at a Lower Pressure than Intended

A New Radiator and Shroud are Used A New Radiator and Shroud are Used

Updated Predelivery/Revisit Checklists Are Now Used Updated Predelivery/Revisit Checklists Are Now Used

REPLACEMENT OF THE FUEL RATIO CONTROL DIAPHRAGM REPLACEMENT OF THE FUEL RATIO CONTROL DIAPHRAGM

CHECK FOR PROPER TORQUE ON THE ELECTRIC STARTER MORTOR NUTS CHECK FOR PROPER TORQUE ON THE ELECTRIC STARTER MORTOR NUTS

8F-3469 O-Ring Seal Failures May Be Caused by a Transmission Clutch Shaft That Is Too Short 8F-3469 O-Ring Seal Failures May Be Caused by a Transmission Clutch Shaft That Is Too Short

Trunnion Support for the Rear Oscillating Axle Should be Inspected for Cracks Trunnion Support for the Rear Oscillating Axle Should be Inspected for Cracks

Use of the Engine Shutdown Switch or Low Engine Speeds Can Cause Loss of Speed Sensor Diagnostic Codes Use of the Engine Shutdown Switch or Low Engine Speeds Can Cause Loss of Speed Sensor Diagnostic Codes

Low Engine Speed May Be Caused by a Breather Malfunction in the Non-Metallic Fuel Cap Low Engine Speed May Be Caused by a Breather Malfunction in the Non-Metallic Fuel Cap

Autolube is Now Standard and Parts are Available Autolube is Now Standard and Parts are Available

Bypass Schedule May Be Affected when Machine Security System (MSS) Automatically Adjusts to North American Daylight Savings Time Bypass Schedule May Be Affected when Machine Security System (MSS) Automatically Adjusts to North American Daylight Savings Time