Acceleration or Deceleration Switch May Stick on 185-1106 or 208-6100 Handles Used on the Transmission/Steering Joystick Caterpillar

Acceleration or Deceleration Switch May Stick on 185-1106 or 208-6100 Handles Used on the Transmission/Steering Joystick

Usage:

Acceleration or Deceleration Switch May Stick on <a class="catalog_a_num" href="https://avspare.com/caterpillar/handle/1851106/">185-1106</a> or <a class="catalog_a_num" href="https://avspare.com/caterpillar/control/2086100/">208-6100</a> Handles Used on the Transmission/Steering Joystick

CONFIDENTIAL TIBU3656-00

Show/hide table

TECHNICAL INFORMATION BULLETIN	JULY 24, 2002
Small Track-Type Tractors	D3G XL (CFC) D3G LGP (CFF) D4G XL (CFN) D4G LGP (FDC) D5G XL (FDH) D5G LGP (FDW)
	Component Code: 3033

SUBJECT: Acceleration or Deceleration Switch May Stick on 185-1106 or 208-6100 Handles Used on the Transmission/Steering Joystick.

PROBLEM:

Reports from the field indicate that the acceleration or deceleration switches may stick, leading to one or more of the following symptoms:

Logged service codes of CID 1701 FMI 02 (acceleration switch) or CID 1702 FMI 02 (deceleration switch).
Transmission stuck in 1^st or 2^nd gear.
Transmission will not up shift.
Transmission will not down shift.

SOLUTION:

Caterpillar engineering is aware of this problem and a solution is being investigated. In the meantime, follow this procedure to correct a sticking problem in lieu of, or prior to, replacing the handle.

1. Remove any clear plastic shipping wrap on the handle. This wrap can cause the switch to stick.

COPYRIGHT 2002 CATERPILLAR
ALL RIGHTS RESERVED

Caterpillar Information System:

Installation and Replacement Procedure for Greased Linkage Pin Joints on 992G Wheel Loaders Installation and Replacement Procedure for Greased Linkage Pin Joints on 992G Wheel Loaders

REPLACEMENT OF THE HEATER MOTOR AND BLOWER WHEEL REPLACEMENT OF THE HEATER MOTOR AND BLOWER WHEEL

INSTALLATION OF STOPS ON C-FRAME AND BLADE OF D6M INSTALLATION OF STOPS ON C-FRAME AND BLADE OF D6M

Proper Inspection of the Greased Joints Proper Inspection of the Greased Joints

Proper assembly of the fan drive pump increases performance and lengthens service life Proper assembly of the fan drive pump increases performance and lengthens service life

THE POSITIVE BATTERY CABLE MAY RUB TH E TORQUE CONVERTER LINES THE POSITIVE BATTERY CABLE MAY RUB TH E TORQUE CONVERTER LINES

ENGINE OIL DIPSTICK MAY NOT BE THE CORRECT LENGTH ENGINE OIL DIPSTICK MAY NOT BE THE CORRECT LENGTH

Product Link Modules Are Not Reporting Events or Fuel Consumption Product Link Modules Are Not Reporting Events or Fuel Consumption

Error in 213-8799 Monitor Software (Payload Control System) Error in 213-8799 Monitor Software (Payload Control System)

Loose Cartridge Screws In Implement Pump Do Not Constitute A Pump Failure Loose Cartridge Screws In Implement Pump Do Not Constitute A Pump Failure

REWORK ON THE DETENT PLATE AND THE DETENT ASSEMBLY REWORK ON THE DETENT PLATE AND THE DETENT ASSEMBLY

THE PARKING BRAKE GROUP MAY BECOME LOOSE THE PARKING BRAKE GROUP MAY BECOME LOOSE

Incorrect Speed Sensor Wiring Causes Fill Calibration to Abort Incorrect Speed Sensor Wiring Causes Fill Calibration to Abort

Early Detection Can Prevent Crack Growth into A-Pin Bore Early Detection Can Prevent Crack Growth into A-Pin Bore

USE THE 2P-4005 ENGINE OIL FILTER ASSEMBLY TO REPLACE 1R-0716 ENGINE OIL FILTER ASSEMBLY USE THE 2P-4005 ENGINE OIL FILTER ASSEMBLY TO REPLACE 1R-0716 ENGINE OIL FILTER ASSEMBLY

The Pins for the Sidebar Bend or Break The Pins for the Sidebar Bend or Break

PREVENTING CRACKS IN THE REAR TRACK ROLLER FRAME PREVENTING CRACKS IN THE REAR TRACK ROLLER FRAME

Temporary Change to the PS41004 Hood Skin Repair Procedure for D9R Track-Type Tractors Temporary Change to the PS41004 Hood Skin Repair Procedure for D9R Track-Type Tractors

Cracks have been found in the radome of the 167-8930 GPS Antenna and the 194-8015 GPS Antenna Cracks have been found in the radome of the 167-8930 GPS Antenna and the 194-8015 GPS Antenna

CASE DRAIN RETURN SCREEN ON D11R AND D11R CARRYDOZER HYDRAULIC TANK MUST BE CHECKED CASE DRAIN RETURN SCREEN ON D11R AND D11R CARRYDOZER HYDRAULIC TANK MUST BE CHECKED

Caterpillar is releasing replacement software for PCS version 2.07A and 2.07AR software (Cat p/n 213-8794 and 213-8799 respectively) Caterpillar is releasing replacement software for PCS version 2.07A and 2.07AR software (Cat p/n 213-8794 and 213-8799 respectively)

WIRING DIAGRAM FOR INSTALLING THE MARINE POWER DISPLAY WIRING DIAGRAM FOR INSTALLING THE MARINE POWER DISPLAY

Tilt Cylinder Dump Noise Tilt Cylinder Dump Noise

Power Train Oil Filter Bypass Alarm Activates at a Lower Pressure than Intended Power Train Oil Filter Bypass Alarm Activates at a Lower Pressure than Intended