Exhaust Elbow - Remove and Install
拆卸步骤
Show/hide table
| 所需工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件说明 | 数量 |
| A | 138-7575 | 连杆支架 | 4 |
Show/hide table
| 注意 |
|---|
在检验、保养、测试、调整及维修产品时，务必留心，确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前，要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品，参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
- 拆下螺栓 (1) 。
Show/hide table
 | |
| 图 1 | g01063842 |
- 将工具 (A) 和适当的起吊设备连接在排气弯头 (2) 和涡轮增压器上。
Show/hide table
 | |
| 图 2 | g01064186 |
- 拆卸螺栓 (3) 和 (4) 。
- 拆下排气弯头 (2) 。 拆下排气弯头 (2) 时，继续支撑起涡轮增压器。 排气弯头的重量约为 60 kg (132 lb)。
安装步骤
Show/hide table
| 所需工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件说明 | 数量 |
| A | 138-7575 | 连杆支架 | 4 |
| B | 4C-5599 | 防粘结剂 | 1 |
- 将工具 (A) 和适当的提升设备连接在排气弯头 (2) 上。
Show/hide table
| | |
| 图 3 | g01064186 |
- 定位排气弯头 (2) 。 排气弯头的重量约为 60 kg (132 lb)。
- 将工具 (B) 涂抹到垫圈及螺栓 (3) 和 (4) 的螺纹上。
- 安装螺栓 (3) 和 (4) 。 用 20 ± 2 N·m (15 ± 1 lb ft) 的扭矩拧紧螺栓 (3) 。
- 将工具 (B) 涂抹到垫圈和螺栓 (1) 的螺纹上。 安装螺栓 (1) 。
Show/hide table
| | |
| 图 4 | g01063842 |
Caterpillar Information System:
3126B Petroleum Engine Installation Environment
2004/04/01 The Heat Exchanger Bonnet can be Rotated on Certain Applications {1379}
3406E, C12, C15 and C18 Marine Engines Flash Codes
C7 Marine Engine Cooling System - Check - Overheating
3406E and 3456 Generator Set Engines ECM Will Not Communicate with Other Systems or Display Modules
C-15 Petroleum Engine Auxiliary Water Pump
3406E and 3456 Generator Set Engines Coolant in Engine Oil
G3520C and G3520E Generator Set Engines Turbocharger - Assemble - Dual Turbochargers
3406E, C-10 and C-12 On-highway Engines Accelerator Pedal (Throttle) Position Sensor Circuit - Test
G3520C and G3520E Generator Set Engines Turbocharger - Disassemble - Dual Turbochargers
3406E and 3456 Generator Set Engines Engine Cranks but Will Not Start
G3520C and G3520E Generator Set Engines Turbocharger - Install
3126B Engine for Caterpillar Built Machines CID 0001 FMI 11 Cylinder #1 Injector fault
3126B Engine for Caterpillar Built Machines CID 0002 FMI 11 Cylinder #2 Injector fault
3126B Engine for Caterpillar Built Machines CID 0003 FMI 11 Cylinder #3 Injector fault
3126B Engine for Caterpillar Built Machines CID 0004 FMI 11 Cylinder #4 Injector fault
C15 and C18 Industrial Engines Fuel Filter Base - Disassemble
3126B Engine for Caterpillar Built Machines CID 0005 FMI 11 Cylinder #5 Injector fault
C15 and C18 Industrial Engines Fuel Filter Base - Assemble
3126B Engine for Caterpillar Built Machines CID 0006 FMI 11 Cylinder #6 Injector fault
C15 Petroleum Engines Water Pump - Remove
C-15 Petroleum Engine Troubleshooting
C15 Petroleum Engines Water Pump - Install
3406E, C-10 and C-12 On-highway Engines ATA (SAE J1587 / J1708) Data Link Circuit - Test