Fuel Filter Base - Assemble
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 155-0695 | 螺纹锁固胶 | - |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将 O 形密封圈安装在燃油旁通阀 (2) 上。 将燃油旁通阀安装在燃油滤清器底座组件 (1) 上。
- 将 O 形密封圈安装在燃油单向阀 (5) 上。 将燃油单向阀安装在燃油滤清器底座组件 (1) 上。 拧紧燃油单向阀至扭矩为
28 ± 3 N·m (21 ± 2 lb ft) 。 - 将 O 形密封圈安装到接头 (3) 上。 将接头安装在燃油滤清器底座组件 (1) 上。
- 如有必要,将空心螺柱 (4) 安装到燃油滤清器底座组件 (1) 上。 拧紧空心螺柱至扭矩为
70 ± 15 N·m (52 ± 11 lb ft) 。注: 将工具 (A) 涂抹到锥形锁紧螺柱底座端处的第一个
7.6 ± 0.8 mm (0.30 ± 0.03 inch) 螺纹。
Show/hide table
图 1 | g01063845 |
结束:
- 安装燃油滤清器底座。 请参阅拆解和组装, "燃油滤清器底座 - 安装"。
Caterpillar Information System:
3126B Engine for Caterpillar Built Machines CID 0005 FMI 11 Cylinder #5 Injector fault
C15 and C18 Industrial Engines Fuel Filter Base - Disassemble
3126B Engine for Caterpillar Built Machines CID 0004 FMI 11 Cylinder #4 Injector fault
3126B Engine for Caterpillar Built Machines CID 0003 FMI 11 Cylinder #3 Injector fault
3126B Engine for Caterpillar Built Machines CID 0002 FMI 11 Cylinder #2 Injector fault
3126B Engine for Caterpillar Built Machines CID 0001 FMI 11 Cylinder #1 Injector fault
G3520C and G3520E Generator Set Engines Exhaust Elbow - Remove and Install
3126B Petroleum Engine Installation Environment
2004/04/01 The Heat Exchanger Bonnet can be Rotated on Certain Applications {1379}
3406E, C12, C15 and C18 Marine Engines Flash Codes
C7 Marine Engine Cooling System - Check - Overheating
3406E and 3456 Generator Set Engines ECM Will Not Communicate with Other Systems or Display Modules
3126B Engine for Caterpillar Built Machines CID 0006 FMI 11 Cylinder #6 Injector fault
C15 Petroleum Engines Water Pump - Remove
C-15 Petroleum Engine Troubleshooting
C15 Petroleum Engines Water Pump - Install
3406E, C-10 and C-12 On-highway Engines ATA (SAE J1587 / J1708) Data Link Circuit - Test
C15 and C18 Industrial Engines Belt Tightener - Remove
C15 and C18 Industrial Engines Belt Tightener - Install
C15 and C18 Industrial Engines Belt Tightener - Disassemble
C15 and C18 Industrial Engines Belt Tightener - Assemble
C-15 Petroleum Engine Fuel System - Prime
2004/06/07 Replace the Fuel Injector Hold-Down Bolt When You Service Electronic Unit Injectors {1251, 1290}
2004/05/01 Use The Correct Stub Shaft For The Crankshaft {1237, 1359}