Water Pump
Show/hide table
图 1 | g01061721 |
(1) O 形密封圈
用甘油或经认可的等效物润滑孔。
(2) 轴
-
在将轴压装至叶轮轴前用清洁的发动机机油对其进行润滑。 安装叶轮使叶轮和泵轴之间的尺寸如下所示:
- 尺寸 ... 0.000 ± 0.076 mm (0.0000 ± 0.0030 in)
(3) 螺塞
- 扭矩 ... 8 ± 1 N·m (71 ± 8 lb in)
(4) 密封组件
按以下步骤安装密封组件。
- 使用 207-1600 橡胶润滑剂 来辅助装配。
- 使用安装工具并用手将陶瓷环和橡胶密封压至泵壳体内。
- 将弹簧从密封组件中拆下。
- 使用安装工具并用手将密封组件推至轴上,直到密封表面间有轻微接触。
- 安装弹簧。
Show/hide table
注意 |
---|
操作不当可能损坏陶瓷密封。 如果轴在安装过程中受到碰撞,泵内的陶瓷密封可能会出现裂缝并导致冷却液从排水孔中漏出。 安装时小心不要令轴产生硬性接触。 安装时应将泵完全插入。 安装时不要让轴支撑泵的重量。 |
(5) 油封
遵照以下指导安装油封:
- 安装油封并进行干燥。
- 要在将油封从装运衬套上拆下后的 2 分钟内将油封安装好。
- 安装油封时动作要缓慢且平稳。
- 使用正确的安装工具。
(6) 锁紧螺母
- 锁紧螺母的扭矩 ... 300 ± 30 N·m (221 ± 22 lb ft)
- 锁紧螺母调整螺钉的扭矩 ... 4 ± 1.25 N·m (35 ± 11 lb in)
空气压力为 138 kPa (20 psi) 时水密封的每分钟最大泄漏量 ... 20 cc (1.22 cu in)
空气压力为 138 kPa (20 psi) 时油封的每分钟最大泄漏量 ... 24 Cc (1.46 Cu in)
Caterpillar Information System:
C7 On-highway Engine Air Compressor
3126B Petroleum Engine Refill Capacities and Recommendations
C-15 Petroleum Engine Auxiliary Water Pump - Assemble
C-15 Petroleum Engine Auxiliary Water Pump - Disassemble
3126B Petroleum Engine Diagnostic Flash Code Retrieval
3516B and 3516B High Displacement Engines for 994D and 994F Wheel Loaders Accessory Drive (Upper Left Hand)
SCJ and 8SC Series Alternators Stator - Test
SCJ and 8SC Series Alternators Field Winding - Test
SCJ and 8SC Series Alternators Capacitor - Test
G3520C and G3520E Engines Temperature Sensor - Thermocouple
3126B Petroleum Engine Throttle Position Sensor Circuit - Test
C-10 and C-15 Petroleum Engines Injector Solenoid Circuit - Test
3126B Petroleum Engine Engine Oil and Filter - Change
C-15 Petroleum Engine Aftercooler - Install
C-15 Petroleum Engine Aftercooler - Remove
C9 On-highway Engine Camshaft
C-15 Petroleum Engine Fuel Priming Pump - Remove and Install
C-15 Petroleum Engine Fuel Filter Base - Remove
C-15 Petroleum Engine Fuel Filter Base - Install
C9 Urban Transit Bus Engine Air Inlet Elbow
3126B Petroleum Engine Reference Material
C13, C15, and C18 Generator Set Engines Basic Engine
C13 Engines Engine Oil Level - Check
C-15 Petroleum Engine Air Inlet and Exhaust System