Belt Tension Chart
Show/hide table
Use of standard belts on this engine may cause an explosion which may result in personal injury or death. Only non-static belts should be used on this engine. |
Note: Do not use the belt tension charts for belts with tensioners that are spring loaded.
Show/hide table
Belt Tension Chart     | |||||||||||
Size of Belt     | Width of Belt     | Gauge Reading     | Kent-Moore Gauge Numbers     | ||||||||
Belt Tension "Initial" (1) |
Belt Tension "Used" (2) (3)     |
Number of the Old Gauge     | Number of the New Gauge     | ||||||||
3/8     | 10.72 mm (0.422 inch)     |
534 ± 111 N (120 ± 25 lb)     |
400 ± 22 N (90 ± 5 lb)     |
BT-33-97     | BT 3397     | ||||||
1/2     | 13.89 mm (0.547 Inch)     |
578 ± 111 N (130 ± 25 lb)     |
445 ± 44 N (100 ± 10 lb)     |
BT-33-97     | BT 3397     | ||||||
5V     | 15.88 mm (0.626 Inch)     |
712 ± 111 N (160 ± 25 lb)     |
445 ± 44 N (100 ± 10 lb)     |
BT-33-72C     | BT 3372C     | ||||||
11/16     | 17.48 mm (0.688 Inch)     |
712 ± 111 N (160 ± 25 lb)     |
445 ± 44 N (100 ± 10 lb)     |
BT-33-72C     | BT 3372C     | ||||||
3/4     | 19.05 mm (0.750 Inch)     |
712 ± 111 N (160 ± 25 lb)     |
445 ± 44 N (100 ± 10 lb)     |
BT-33-72C     | BT 3372C     | ||||||
15/16     | 23.83 mm (0.938 Inch)     |
712 ± 111 N (160 ± 25 lb)     |
445 ± 44 N (100 ± 10 lb)     |
BT-33-77     | BT 3372C     | ||||||
8PK     | 27.82 mm (1.095 inch)     |
1068 ± 111 N (240 ± 25 lb)     |
890 ± 44 N (200 ± 10 lb)     |
BT-33-109     | BT 33109     | ||||||
6PK     | 20.94 mm (0.824 Inch)     |
801 ± 111 N (180 ± 25 lb)     |
667 ± 44 N (150 ± 10 lb)     |
BT-33-109     | BT 33109     | ||||||
Measure the tension of the belt that is farthest from the engine.     |
Show/hide table
( 1 ) | Belt tension "Initial" is for a new belt. |
( 2 ) | Belt tension "Used" is for a belt that has operated for 30 minutes or more of operation at the rated speed. |
( 3 ) | If a belt falls below the "Used" belt tension, the belt should be tightened again to the high side of the "Used" belt tension. |
Show/hide table
DAYCO Supplied Belts Only     | ||||
---|---|---|---|---|
Size of Belt     | Belt Tension "Initial"     |
Belt Tension "Used" (4)     |
||
0.380 (V-Belt)     | 623 ± 22 N (140 ± 5 lb)     |
245 - 534 N (100 ± 5 lb)     |
||
0.440 (V-Belt)     | 667 ± 22 N (150 ± 5 lb)     |
245 - 534 N (100 ± 5 lb)     |
||
0.500 (V-Belt)     | 712 ± 22 N (160 ± 5 lb)     |
245 - 534 N (100 ± 5 lb)     |
||
0.600 (V-Belt)     | 779 ± 22 N (175 ± 5 lb)     |
245 - 534 N (100 ± 5 lb)     |
||
0.660 (V-Belt)     | 890 ± 22 N (200 ± 5 lb)     |
245 - 534 N (100 ± 5 lb)     |
||
0.790 (V-Belt)     | 890 ± 22 N (200 ± 5 lb)     |
245 - 534 N (100 ± 5 lb)     |
||
4 - RIB PVK     | 623 ± 22 N (140 ± 5 lb)     |
267 - 445 N (90 ± 5 lb)     |
||
5 - RIB PVK     | 779 ± 22 N (175 ± 5 lb)     |
334 - 556 N (100 ± 5 lb)     |
||
6 - RIB PVK     | 934 ± 22 N (210 ± 5 lb)     |
400 - 667 N (130 ± 5 lb)     |
||
8 - RIB PVK     | 1157 ± 22 N (260 ± 5 lb)     |
534 - 890 N (180 ± 5 lb)     |
||
10 - RIB PVK     | 1557 ± 22 N (350 ± 5 lb)     |
667 - 1112 N (230 ± 5 lb)     |
||
12 - RIB PVK     | 1869 ± 22 N (420 ± 5 lb)     |
800 - 1335 N (270 ± 5 lb)     |
||
15 - RIB PVK     | 2336 ± 22 N (525 ± 5 lb)     |
1000 - 1669 N (350 ± 5 lb)     |
Show/hide table
( 4 ) | If a belt falls below the "Used" belt tension, the belt should be tightened again to the "Initial" belt tension. |
Caterpillar Information System:
C18 Generator set and C18 Marine Engines Fuel Transfer Pump - Install
C18 Generator set and C18 Marine Engines Fuel Transfer Pump - Remove
3126B Petroleum Engine Engine Crankcase Pressure (Blowby) - Test
G3600 Engines Crankshaft Vibration Damper - Inspect
C13, C15, and C18 Generator Set Engines Ether Injection System - Test
G3300 Engines Gas Pressure Regulator - Check
3412E Petroleum Engine System Configuration Parameters
C15 and C18 Petrolem Generator Set Engines Switch Circuits - Test
C-15 Petroleum Engine Turbocharger
3408E and 3412E Engines for Caterpillar Built Machines Engine Oil Temperature Sensor - If Equipped
C9 On-Highway Truck Engines Modulating Valve - Remove and Install
Center Steering Arm Straight Bore Inspection and Salvage Procedure for Off-Highway Trucks {4305} Center Steering Arm Straight Bore Inspection and Salvage Procedure for Off-Highway Trucks {4305}
G3300 Engines Engine - Clean
G3520C and G3520E Engines Thermostatic Valve
G3600 Engines Cooling System Coolant Level - Check
2004/03/01 Listing of Deutsch Connector Components {7553}
C18 Petroleum Generator Sets Engine Description
G3520C and G3520E Engines Thermostatic Valve
3126B Petroleum Engine Water Temperature Regulator
C13, C15, and C18 Generator Set Engines Engine Shutdown Switch Circuit - Test
2004/05/01 New Piston For Marine Auxiliary And Industrial Engines Reduces Light Load Oil Consumption {1214}
C13, C15, and C18 Generator Set Engines Digital Sensor Supply Circuit - Test
3406E, C-10 and C-12 On-highway Engines System Overview
3412E Petroleum Engine Engine Cranks but Will Not Start