Cooling System Coolant Level - Check
Show/hide table
Show/hide table
图 1 | g00750429 |
(1) 加注口盖
(2) 目测液位计 |
如果发动机配备了目测液位计,观察目测液位计中冷却液的位置。 在正常工作温度下,正确的冷却液液位是在目测液位计的上半部。 如果冷却液液位过低,添加正确的冷却液混合液。
Show/hide table
加压的系统: 热的冷却液能造成严重的烫伤。 在发动机停机,等待冷却系统部件冷却下来后再打开冷却系统加注口盖。 缓慢松开冷却系统加注口盖,以释放掉所有压力。 |
发动机停机并冷却后检查冷却液液位。 只有在停止发动机后,冷却系统的压力盖冷却到可以徒手触摸时,才能检查冷却液液位。
慢慢拆下冷却系统加注口盖,以释放全部压力。 将冷却液液位保持在距加注管底部
注: 有关应使用的正确的冷却液混合液,请参阅操作和保养手册, "冷却液加注容量和建议"
(保养部分)。
- 使发动机停机。 让发动机冷却下来。
- 慢慢拆下冷却系统加注口盖,以释放全部压力。 将正确的冷却液混合液加注到冷却液加注口管道。
Show/hide table
图 2 g00103639 密封垫 - 清洁冷却系统加注口盖。 检查加注口盖密封圈的状况。 如果冷却系统加注口盖密封圈损坏,请用新件更换旧的冷却系统加注口盖。 安装冷却系统加注口盖。
- 起动发动机。 检查冷却系统是否渗漏。
Caterpillar Information System:
G3520C and G3520E Engines Thermostatic Valve
G3300 Engines Engine - Clean
3126B Petroleum Engine Belt Tension Chart
C18 Generator set and C18 Marine Engines Fuel Transfer Pump - Install
C18 Generator set and C18 Marine Engines Fuel Transfer Pump - Remove
3126B Petroleum Engine Engine Crankcase Pressure (Blowby) - Test
G3600 Engines Crankshaft Vibration Damper - Inspect
C13, C15, and C18 Generator Set Engines Ether Injection System - Test
G3300 Engines Gas Pressure Regulator - Check
3412E Petroleum Engine System Configuration Parameters
C15 and C18 Petrolem Generator Set Engines Switch Circuits - Test
C-15 Petroleum Engine Turbocharger
2004/03/01 Listing of Deutsch Connector Components {7553}
C18 Petroleum Generator Sets Engine Description
G3520C and G3520E Engines Thermostatic Valve
3126B Petroleum Engine Water Temperature Regulator
C13, C15, and C18 Generator Set Engines Engine Shutdown Switch Circuit - Test
2004/05/01 New Piston For Marine Auxiliary And Industrial Engines Reduces Light Load Oil Consumption {1214}
C13, C15, and C18 Generator Set Engines Digital Sensor Supply Circuit - Test
3406E, C-10 and C-12 On-highway Engines System Overview
3412E Petroleum Engine Engine Cranks but Will Not Start
3126B Petroleum Engine Engine Oil Temperature Is Too High
3126B Petroleum Engine Excessive Black Smoke
3126B Petroleum Engine Excessive Fuel Consumption