Gear Group (Front) - Remove
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件说明 | 数量 |
A | 1P-0510 | 起子总成 | 1 |
开始:
- 拆卸前壳体。 请参阅 拆解和组装, "壳体(前) - 拆卸" 。
- 必要时,拆下空气压缩机。 请参阅拆解和组装 , "空气压缩机 - 拆卸和安装" 。
- 必要时,拆下水泵。 请参阅拆解和组装 , "水泵 - 拆卸" 。
- 必要时,拆下辅助水泵。 参考拆解与组装 , "辅助水泵 - 拆卸 "。
- 如有必要,拆下燃油输油泵。 请参阅拆解和组装 , "燃油输油泵 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在拆卸凸轮轴齿轮时,不要转动曲轴或凸轮轴。 如果在安装时没有正确调整前齿轮总成的正时,活塞与气门之间将会发生干涉,进而导致发动机损坏。 |
注: 务必标记每个齿轮的朝向以便于安装。
- 拆下螺栓 (2) 和止推板 ( 1)。
Show/hide table
图 2 g01008430 - 拆下密封板 (3) 和适配器 ( 4)。
Show/hide table
图 3 g01008431 - 将 O 形密封圈 (5) 和 O 形密封圈 (6) 从密封板 ( 3) 上拆下。
Show/hide table
图 4 g01101536 - 拆下螺栓 (8)、板 ( 9)和可调节惰轮齿轮组件 ( 7)。
- 利用工具 (A) 将套筒轴承从可调节惰齿轮组件 ( 7) 上拆下。
Show/hide table
图 5 g01101045 - 拆下螺栓 (11)、板 ( 12), 和惰轮齿轮组件 ( 10)。
- 利用工具 (A) 将套筒轴承从惰齿轮组件 ( 10) 上拆下。
Show/hide table
图 6 g01101048 - 拆下螺栓 (14)、板 ( 15) 和齿轮组组件 (13 )。
- 使用工具 (A) 并从齿轮组组件 ( 13) 上拆下套筒轴承。
Show/hide table
图 7 g01101050 注: 必须拆下短型轴组件 ( 16) 以便拆下板 (22)。 需要对组件处凸轮轴齿轮和可调节惰轮齿轮组件的间隙进行调节。
- 拆下螺母 (17) 并拆下短型轴组件 ( 16)。
注: 必须拆下短型轴组件 ( 16) 以便拆下板 (22)。
- 拆下螺母 (19) 并拆下短型轴 ( 18)。
- 拆下螺栓 (21) 并拆下短型轴 ( 20)。
- 卸下将板 (22) 固定在缸体上的锁紧螺栓 ( 23)。 拆下板 (22)。
- 如果螺栓 (24) 松开或者螺纹损坏,请将螺柱从前板上拆下。
Show/hide table
图 8 g01101052 - 将整体式密封 (25) 从缸体上拆下。
Show/hide table
图 1 | g01008429 |
Caterpillar Information System:
C3.4 IND Industrial Engine Fuel System Primary Filter/Water Separator - Drain
C3.4 IND Industrial Engine Fuel System - Prime
2003/07/14 Policy for Reusing the Turbocharger Turbine Housing {1065}
2003/07/01 Policy for Reusing the Turbocharger Turbine Housing {1052, 1065, 7754}
2003/07/01 Make Sure That the Shunt Tank's Filler Neck is Vented {1354, 1377}
2003/07/01 Align the Balancer Gears {1204, 1206, 1220}
2003/07/01 Improved Auxiliary Pumps are Used {1371}
C15 On-highway Engine Flywheel Housing - Remove and Install
2012/10/26 Policy for the Reuse of the Turbocharger Turbine Housing {1065}
2003/08/01 An Improved Air Lines Group and Carburetor Groups Are Available {1071, 1266}
3456 Generator Sets Rotating Rectifier - Test
3114, 3116, and 3126 Engines for Caterpillar Built Machines Camshaft - Install
C15 On-highway Engine Gear Group (Front) - Install
2003/08/01 New Fabricated Tool for Piston Pin Installation {1225}
G3500 Engines Duplex Oil Filter - Adjust
3406C Marine Auxiliary Generator Set Gauges and Indicators
C3.3 Industrial Engine Fuel Injector - Install
C11, C13 and C15 On-highway Engines Engine/Gear Parameters
C11, C13 and C15 On-highway Engines Idle Parameters
C11, C13 and C15 On-highway Engines Engine Monitoring Parameters
C11, C13 and C15 On-highway Engines Dedicated PTO Parameters
C11, C13 and C15 On-highway Engines Vehicle Speed Parameters
C11, C13 and C15 On-highway Engines Input Selections
Cat® Digital Voltage Regulator Remote Communication