Camshaft Gear - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 1P-2320     | Combination Puller     | 1     |
Start By:
- Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Use Tooling (A) to remove camshaft gear (4) from camshaft (2) . Remove key (1) and thrust plate (3) .
Note: Do not lose the key from the camshaft gear.
Show/hide table
Illustration 1 | g01993021 |
Installation Procedure
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Inspect the camshaft gear, the key, and the thrust plate for wear or damage.
- Install key (1) and thrust plate (3) . Raise the temperature of camshaft gear (4) and install camshaft gear (4) on camshaft (2) .
Note: Ensure that the key is installed on the camshaft. When you install the camshaft gear, ensure that the marked teeth are facing toward the front. If necessary, tap the gear with a soft hammer in order to seat the key in the keyway.
Show/hide table
Illustration 2 | g01993021 |
End By: Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install".
Caterpillar Information System:
3044C Industrial Engine and Engines for Caterpillar Built Machines Camshaft - Remove and Install
G3304 and G3306 Engines Inlet and Exhaust Valves - Remove and Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Lifter Group - Remove and Install
G3304 and G3306 Engines Water Directors - Remove and Install
3500B Series II Marine Engines Air Shutoff System
3044C Industrial Engine and Engines for Caterpillar Built Machines Cylinder Head - Install
PM820, PM822, and PM825 Cold Planer Engine Valve Lash - Check
3044C Industrial Engine and Engines for Caterpillar Built Machines Cylinder Head - Remove
3500B Series II Marine Engines E039 Low Engine Oil Pressure Derate
G3304 and G3306 Engines Valve Seat Inserts - Remove and Install
C-10, C-12, C-15 and C-16 Industrial Engines E004 Engine Overspeed Shutdown
3044C Industrial Engine and Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Install
C9 On-highway Engine Water Pump
3508B, 3508C, 3512B, 3512C, 3516B and and 3516C Marine Engines Product Description
3500C Marine Propulsion Engines Specifications
3508B, 3508C, 3512B, 3512C, 3516B and and 3516C Marine Engines Refill Capacities
3044C Industrial Engine and Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Inlet Manifold - Remove
3044C Industrial Engine and Engines for Caterpillar Built Machines Inlet Manifold - Install
3500B Locomotive Engines Electronic Control Module (ECM)
3044C Industrial Engine and Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove
G3500 Engines MID 014 - CID 0330 - FMI 11 Propane Timing Mode requested
G3304 and G3306 Engines Air Cleaner - Remove
3044C Industrial Engine and Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble