Specifications
Show/hide table
发动机技术规格     | |||||
项目     | 3508B 发动机     | 3512B 发动机 3512C 发动机     |
3516B 发动机 3516C 发动机     |
||
标准 | 标准     | 高排量     | 标准     | 高排量     | |
额定转速(rpm)     | 1200 至 1925     | ||||
怠速转速 (rpm)     | 450 至 900     | ||||
气缸及排列     | V 型 60 度 8 缸     | V 型 60 度 12 缸     | V 型 60 度 16 缸     | ||
缸径     | 170 mm (6.7 in.)     |
||||
行程     | 190 mm (7.5 in.)     |
190 mm (7.5 in.)     |
215 mm (8.5 in.)     |
190 mm (7.5 in.)     |
215 mm (8.5 in.)     |
类型     | 4 冲程     | ||||
压缩比     | 14:1     | ||||
进气方式     | 涡轮增压式     | ||||
冷却涡轮增压空气的方法     | 水套水后冷却     | ||||
独立回路后冷式 | |||||
每一缸的排量     | 4.3 L (263 in 3 )     |
4.3 L (263 in 3 )     |
4.9 L (299 in3)     |
4.3 L (263 in 3 )     |
4.9 L (299 in3)     |
总排量     | (34.5 L) (2105 in 3 )     |
(51.8 L) (3158 in 3 )     |
(58.5 L) (3570 in3)     |
(69.1 L) (4210 in 3 )     |
(78 L) (4760 in3)     |
旋转(飞轮)     | 逆时针旋转(标准)     | ||||
顺时针旋转(可选) | |||||
燃油     | 参阅操作和保养手册, "加注容量和建议" (保养部分)。     | ||||
燃油喷射方法     | 电子喷油器     | ||||
起动方法     | 电起动马达     | ||||
空气起动马达 | |||||
排气系统的设计背压     | 2.5 kPa (10 in 的 H2O)     |
||||
最大允许背压     | 5.0 kPa (20 in 的 H2O)     |
||||
最大进气阻力     | 6.2 kPa (25 in 的 H2O)     |
||||
空气滤清器     | 单滤芯     | ||||
双滤芯 |
Show/hide table
图 1 | g00739600 |
3508B 发动机 (A) 进气门 (B) 排气门 (C) 飞轮 |
Show/hide table
图 2 | g00749769 |
3512B 发动机 3512C 发动机 (A) 进气门 (B) 排气门 (C) 飞轮 |
Show/hide table
图 3 | g00749770 |
3516B 发动机 3516C 发动机 (A) 进气门 (B) 排气门 (C) 飞轮 |
Caterpillar Information System:
3508B, 3508C, 3512B, 3512C, 3516B and and 3516C Marine Engines Product Description
C9 On-highway Engine Water Pump
3044C Industrial Engine and Engines for Caterpillar Built Machines Camshaft Gear - Remove and Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Camshaft - Remove and Install
G3304 and G3306 Engines Inlet and Exhaust Valves - Remove and Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Lifter Group - Remove and Install
G3304 and G3306 Engines Water Directors - Remove and Install
3500B Series II Marine Engines Air Shutoff System
3044C Industrial Engine and Engines for Caterpillar Built Machines Cylinder Head - Install
PM820, PM822, and PM825 Cold Planer Engine Valve Lash - Check
3044C Industrial Engine and Engines for Caterpillar Built Machines Cylinder Head - Remove
3500B Series II Marine Engines E039 Low Engine Oil Pressure Derate
3508B, 3508C, 3512B, 3512C, 3516B and and 3516C Marine Engines Refill Capacities
3044C Industrial Engine and Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Inlet Manifold - Remove
3044C Industrial Engine and Engines for Caterpillar Built Machines Inlet Manifold - Install
3500B Locomotive Engines Electronic Control Module (ECM)
3044C Industrial Engine and Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove
G3500 Engines MID 014 - CID 0330 - FMI 11 Propane Timing Mode requested
G3304 and G3306 Engines Air Cleaner - Remove
3044C Industrial Engine and Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
G3500 Engines MID 014 - CID 0331 - FMI 11 Ignition Shutdown requested
3044C Industrial Engine and Engines for Caterpillar Built Machines Pistons and Connecting Rods - Assemble
G3500 Engines MID 014 - CID 0591 - FMI 12 EEPROM checksum fault or ECM not programmed