Housing (Front) - Remove
Start By:
- Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install".
- Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and Install".
- Remove the idler gear. Refer to Disassembly and Assembly, "Idler Gear - Remove and Install".
- Remove the camshaft gear. Refer to Disassembly and Assembly, "Camshaft Gear - Remove and Install".
- Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump - Remove".
- Remove the air compressor, if equipped. Refer to Disassembly and Assembly, "Air Compressor - Remove and Install".
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
- Remove bolts (2) that fasten the front housing (1) to the cylinder block.
- Remove front housing (1). Remove gasket (3) from the cylinder block.
Show/hide table
Illustration 2 g00949780 - Remove thrust washer (6) from camshaft (7).
Show/hide table
| |
| Illustration 1 | g00944252 |
Caterpillar Information System:
3056E Industrial Engine Housing (Front) - Install
C7 On-highway Engine Air Inlet Elbow
CIPI UNDERCARRIAGE Arrangements: 9Q-5240, 9Q-5241, 9Q-5242, 9Q-5250, 9Q-5253, 9Q-5265, 9Q-5266, 9Q-5392, 9Q-5393, 9Q-5478, 9Q-5504, 9Q-5621, 9Q-5643, 9Q-5651, 9Q-5709, 9Q-5718, 9Q-5723, 9Q-5724, 9Q-5725, 9Q-5726, 9Q-5731, 9Q-5747, 9Q-5780, 9Q-5792, 9 Track Roller Mounting
3056E Industrial Engine Front Cover - Remove and Install
C7 Engines for Combat and Tactical Vehicles 0252-12 Personality Module Fault (52)
C9 Urban Transit Bus Engine Electronic Control System Components
C18 Generator set and C18 Marine Engines Aftercooler - Install
C18 Generator set and C18 Marine Engines Aftercooler - Remove
3056E Industrial Engine Crankshaft Front Seal - Install
C18 Generator set and C18 Marine Engines Exhaust Manifold - Remove and Install
2002/11/25 New Cover Seals are Available {1107, 1201, 1316, 1317, 1336}
3056E Industrial Engine Crankshaft Front Seal - Remove
3056E Industrial Engine Water Temperature Regulator - Remove and Install
C7 Petroleum Engines General Information
3056E Industrial Engine Water Outlet Manifold - Remove and Install
3500B Engines Thermostatic Valve
G3500B Engines Water Temperature Regulator
C15 On-highway Engine Fuel Filter Lines
C7 Petroleum Engines Air Inlet and Exhaust System
3056E Industrial Engine Water Pump - Remove and Install
3126B Marine Engines CID 0102 FMI 03 Boost Pressure Sensor short to +batt
C11, C13 and C15 On-highway Engines Injector Code - Calibrate
C7 Petroleum Engines Basic Engine
3126B Marine Engines CID 0102 FMI 04 Boost Pressure Sensor short to ground