Engine Oil Level - Check
Show/hide table
Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact the skin. |
Show/hide table
Illustration 1 | g00854589 |
(1) Engine oil filler cap (2) Engine oil level gauge |
Show/hide table
Illustration 2 | g00110310 |
(Y) "ADD" mark (X) "FULL" mark |
Show/hide table
NOTICE |
---|
Perform this maintenance with the engine stopped. |
- Maintain the engine oil level between "ADD" mark (Y) and "FULL" mark (X) on engine oil level gauge (1). Do not fill the crankcase above "FULL" mark (X) .
Note: Before you perform this maintenance, do not operate the engine for at least 10 minutes in order to allow the engine oil to return to the engine oil pan.
- Remove engine oil filler cap (2) and add engine oil, if necessary. Clean the engine oil filler cap. Reinstall the engine oil filler cap.
Show/hide table
NOTICE |
---|
Operating your engine when the oil level is above the "FULL" mark could cause your crankshaft to dip into the oil. The air bubbles created from the crankshaft dipping into the oil reduces the oil's lubricating characteristics and could result in the loss of power. |
Caterpillar Information System:
CIPI UNDERCARRIAGE Arrangements: 3Q6662, 6Z7861, 6Z7885, 6Z7947, 6Z7957, 6Z7999, 9Q5044, 9Q5065, 9Q5082, 9Q5090, 9Q5093, 9Q5115, 9Q5118, 9Q5126, 9Q5135, 9Q5141, 9Q5168, 9Q5175, 9Q5206, 9Q5255, 9Q5259, 9Q5268, 9Q5412, 9Q5436, 9Q5464, 9Q5514, 9Q5617, 9 Final Drive - Disassemble
3054 and 3056 Industrial and Generator Set Engines Water Pump
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Recoil Spring
3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Standby Pump Panel General Information
2002/01/01 The Procedure For The Disassembly And Assembly Of The Gas Admission Valve Has Been Updated {1250}
3512B Engine for SPF343, SPS343, and SPT343 Pumpers Digital Sensor Supply
Automatic Transfer Switches CTS, CTSD Series Network - Test
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Front Idler
Automatic Transfer Switches CTS, CTSD Series Network Card - Configure
Automatic Transfer Switches CTS, CTSD Series Network Card - Replace
3500 Engines for Caterpillar Built Generator Sets Electric Starting Motor
2002/01/01 Corrections to Operation and Maintenance Manual, SEBU6916-04, "3500B Engines and 3500 Engines With EUI Option" , "Maintenance Interval Schedule" {1000, 7500}
3054 and 3056 Marine Generator Set Engines Heat Exchanger
3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Standby Pump Panel Contactor - Test
CPT372 Truck Mounted Pumper Power End Oil and Filter - Change
3408E and 3412E Industrial Engines Circuit Breakers
CIPI UNDERCARRIAGE Arrangements: 3Q6662, 6Z7861, 6Z7885, 6Z7947, 6Z7957, 6Z7999, 9Q5044, 9Q5065, 9Q5082, 9Q5090, 9Q5093, 9Q5115, 9Q5118, 9Q5126, 9Q5135, 9Q5141, 9Q5168, 9Q5175, 9Q5206, 9Q5255, 9Q5259, 9Q5268, 9Q5412, 9Q5436, 9Q5464, 9Q5514, 9Q5617, 9 Final Drive - Install
3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Standby Pump Panel Contactor - Adjust
3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Standby Pump Panel Wiring
3408E and 3412E Industrial Engines Muffler
C12 Marine Engine Inlet Manifold Pressure - Test
3500 Industrial Engines Fuel Injector
3408E and 3412E Industrial Engines Air Cleaner
2002/02/01 New Lines Groups Are Used On The Continuous Prelube System {1307, 1319}