3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Standby Pump Panel Caterpillar

General Information

Usage:

3616 1FN

Troubleshooting the standby pump system may require additional information from the engine's Service Manual. The following manuals may be required for troubleshooting:

Testing and Adjusting, SENR3599, "3606 & 3608 Engines"
Testing and Adjusting, SENR3593, "3612 & 3616 Engines"

The Parts Manual for the engine that is being serviced can also be referenced.

During troubleshooting, inspect all connections before any component is replaced. If these connections are not clean and tight, permanent electrical problems or intermittent electrical problems can result. Check that the wires are pushed into the connectors completely. Make sure that the connections are tight before other tests are made.

Failure of an electrical component can cause the failure of other components. Also, failure of an electrical component can be caused by the failure of other components. Always attempt to correct the cause of an electrical system failure before you replace a component.

Refer to the Testing and Adjusting, "Wiring" section of this manual when you troubleshoot the wiring. Perform continuity checks at the harness connectors in order to locate harness failures. At the connectors of the components, always check the ground circuit. Less than 5 ohms of resistance is required between the ground contacts of the connector and the frame ground. Excessive ground resistance that is greater than 5 ohms can cause incorrect diagnosing of problems.

Caterpillar Information System:

2002/01/01 The Procedure For The Disassembly And Assembly Of The Gas Admission Valve Has Been Updated {1250}

3512B Engine for SPF343, SPS343, and SPT343 Pumpers Digital Sensor Supply

Automatic Transfer Switches CTS, CTSD Series Network - Test

CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Front Idler

Automatic Transfer Switches CTS, CTSD Series Network Card - Configure

Automatic Transfer Switches CTS, CTSD Series Network Card - Replace

3500 Engines for Caterpillar Built Generator Sets Electric Starting Motor

2002/01/01 Corrections to Operation and Maintenance Manual, SEBU6916-04, "3500B Engines and 3500 Engines With EUI Option" , "Maintenance Interval Schedule" {1000, 7500}

3176C and 3196 Engines For Caterpillar Built Machines Housing (Front) - Install

3408C and 3412C Marine Engines Electric Starting Motor

CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Travel Motor

3512B Engine for SPF343, SPS343, and SPT343 Pumpers Analog Sensor Supply

CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Recoil Spring

3054 and 3056 Industrial and Generator Set Engines Water Pump

CIPI UNDERCARRIAGE Arrangements: 3Q6662, 6Z7861, 6Z7885, 6Z7947, 6Z7957, 6Z7999, 9Q5044, 9Q5065, 9Q5082, 9Q5090, 9Q5093, 9Q5115, 9Q5118, 9Q5126, 9Q5135, 9Q5141, 9Q5168, 9Q5175, 9Q5206, 9Q5255, 9Q5259, 9Q5268, 9Q5412, 9Q5436, 9Q5464, 9Q5514, 9Q5617, 9 Final Drive - Disassemble

CPT372 Truck Mounted Pumper Engine Oil Level - Check

3054 and 3056 Marine Generator Set Engines Heat Exchanger

3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Standby Pump Panel Contactor - Test

CPT372 Truck Mounted Pumper Power End Oil and Filter - Change

3408E and 3412E Industrial Engines Circuit Breakers

CIPI UNDERCARRIAGE Arrangements: 3Q6662, 6Z7861, 6Z7885, 6Z7947, 6Z7957, 6Z7999, 9Q5044, 9Q5065, 9Q5082, 9Q5090, 9Q5093, 9Q5115, 9Q5118, 9Q5126, 9Q5135, 9Q5141, 9Q5168, 9Q5175, 9Q5206, 9Q5255, 9Q5259, 9Q5268, 9Q5412, 9Q5436, 9Q5464, 9Q5514, 9Q5617, 9 Final Drive - Install

3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Standby Pump Panel Contactor - Adjust

3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Standby Pump Panel Wiring

3408E and 3412E Industrial Engines Muffler