Contactor - Test
Show/hide table
Contactor     | Description     | Setpoint     |
---|---|---|
OPLAX1     | Contactor for low oil pressure at low speed     | 120 kPa (17 psi)     |
OPLAX2     | Contactor for low oil pressure at high speed     | 320 kPa (46 psi)     |
FPLAX     | Contactor for low fuel pressure     | 140 kPa (20 psi)     |
JWPLAX     | Contactor for low jacket water pressure     | 70 kPa (10 psi)     |
AWPLAX     | Contactor for low after cooler / oil cooler water pressure     | 70 kPa (10 psi)     |
SWPLAX     | Contactor for low sea water pressure     | 70 kPa (10 psi)     |
Show/hide table
Illustration 1 | g00857661 |
Test Valve(Typical example) (1) Pressure contactor (2) Setting screw for the pressure contactor (3) Connection for a pressure contactor (4) Connection for a pressure contactor (5) Test port (6) Test valve |
- Turn the test valve (6) to the isolated position.
- Connect an air hose to the quick connect hose fitting / test port (5) .
- Apply a pressure that is 50 kPa (7 psi) higher than the specified setting of the contactor (1) to the test port (5) .
- Slowly reduce the pressure. Monitor the pressure as the contactor changes states.
- If the contactor (1) changes states at the specified setting within 10 kPa (1.5 psi), then the setting is good. Refer to the Testing and Adjusting, "Contactor - Adjust"section of this manual, if the contactor (1) does not change states at the specified setting.
Caterpillar Information System:
3054 and 3056 Marine Generator Set Engines Heat Exchanger
CPT372 Truck Mounted Pumper Engine Oil Level - Check
CIPI UNDERCARRIAGE Arrangements: 3Q6662, 6Z7861, 6Z7885, 6Z7947, 6Z7957, 6Z7999, 9Q5044, 9Q5065, 9Q5082, 9Q5090, 9Q5093, 9Q5115, 9Q5118, 9Q5126, 9Q5135, 9Q5141, 9Q5168, 9Q5175, 9Q5206, 9Q5255, 9Q5259, 9Q5268, 9Q5412, 9Q5436, 9Q5464, 9Q5514, 9Q5617, 9 Final Drive - Disassemble
3054 and 3056 Industrial and Generator Set Engines Water Pump
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Recoil Spring
3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Standby Pump Panel General Information
2002/01/01 The Procedure For The Disassembly And Assembly Of The Gas Admission Valve Has Been Updated {1250}
3512B Engine for SPF343, SPS343, and SPT343 Pumpers Digital Sensor Supply
Automatic Transfer Switches CTS, CTSD Series Network - Test
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Front Idler
Automatic Transfer Switches CTS, CTSD Series Network Card - Configure
Automatic Transfer Switches CTS, CTSD Series Network Card - Replace
CPT372 Truck Mounted Pumper Power End Oil and Filter - Change
3408E and 3412E Industrial Engines Circuit Breakers
CIPI UNDERCARRIAGE Arrangements: 3Q6662, 6Z7861, 6Z7885, 6Z7947, 6Z7957, 6Z7999, 9Q5044, 9Q5065, 9Q5082, 9Q5090, 9Q5093, 9Q5115, 9Q5118, 9Q5126, 9Q5135, 9Q5141, 9Q5168, 9Q5175, 9Q5206, 9Q5255, 9Q5259, 9Q5268, 9Q5412, 9Q5436, 9Q5464, 9Q5514, 9Q5617, 9 Final Drive - Install
3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Standby Pump Panel Contactor - Adjust
3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Standby Pump Panel Wiring
3408E and 3412E Industrial Engines Muffler
C12 Marine Engine Inlet Manifold Pressure - Test
3500 Industrial Engines Fuel Injector
3408E and 3412E Industrial Engines Air Cleaner
2002/02/01 New Lines Groups Are Used On The Continuous Prelube System {1307, 1319}
3408E and 3412E Industrial Engines CAN Data Link Circuit - Test
3408E and 3412E Industrial Engines Pressure Sensor (Auxiliary)