Electric Starting Motor
Show/hide table
| |
| Illustration 1 | g02849386 |
Show/hide table
| Specification for 107-0997 Electric Starting Motor Gp, and 6V-0501 Electric Starting Motor Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | 5 | 6V-8188 Nut | Torque to |
| 2 | - | - | Current consumption for solenoid assembly at 32 V and 1. For Pull-in windings is 41 ± 3 A 2. For Hold-in windings is 6.3 A max |
| B | - | - | The clearance between the pinion and the housing is |
| 3 | 2 | 4B-2049 Nut | Torque to |
| 4 | 1 | 6V-8188 Nut | A maximum of three cable terminals or wire terminals may be used with the battery terminal nut (3). A maximum of two of the terminals may be equal to or greater than 0 AWG.
Torque to |
| - | - | - | When the electric starting motor is viewed from the drive end, the motor rotates in the clockwise direction.
No load conditions at 1. Speed is 6500 ± 1000 rpm 2. Current draw is 87.5 ± 12.5 A 3. Voltage is 30 VDC |
Caterpillar Information System:
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Travel Motor
3512B Engine for SPF343, SPS343, and SPT343 Pumpers Analog Sensor Supply
3054 and 3056 Marine Generator Set Engines Cylinder Head - Install - 3056 Engine
3054 and 3056 Marine Generator Set Engines Cylinder Head - Remove - 3056 Engine
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Final Drives and Travel Motors
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fan - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fan Drive
2002/02/01 A Cold Junction Compensator Is Now Available As A Service Replacement Part {7490}
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Track Carrier Roller
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Track Roller (Single Flange)
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Track Roller Mounting
Installation Procedure for the 178-2357 Fuel Transfer Pump Gp on the Hydraulic Electronic Unit Injector (HEUI) Pump{1256} Installation Procedure for the 178-2357 Fuel Transfer Pump Gp on the Hydraulic Electronic Unit Injector (HEUI) Pump{1256}
3176C and 3196 Engines For Caterpillar Built Machines Housing (Front) - Install
2002/01/01 Corrections to Operation and Maintenance Manual, SEBU6916-04, "3500B Engines and 3500 Engines With EUI Option" , "Maintenance Interval Schedule" {1000, 7500}
3500 Engines for Caterpillar Built Generator Sets Electric Starting Motor
Automatic Transfer Switches CTS, CTSD Series Network Card - Replace
Automatic Transfer Switches CTS, CTSD Series Network Card - Configure
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Front Idler
Automatic Transfer Switches CTS, CTSD Series Network - Test
3512B Engine for SPF343, SPS343, and SPT343 Pumpers Digital Sensor Supply
2002/01/01 The Procedure For The Disassembly And Assembly Of The Gas Admission Valve Has Been Updated {1250}
3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Standby Pump Panel General Information
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Recoil Spring
3054 and 3056 Industrial and Generator Set Engines Water Pump