Soot Antenna - Remove and Install
- Use a suitable tool to disconnect harness assembly (3) from soot antenna (2).
- Repeat Step 1 to disconnect the remaining harness assembly from the remaining soot antenna.
- Remove soot antenna (2) from the assembly of the Clean Emissions Module (CEM) (1).
- Repeat Step 3 In order to remove the remaining soot antenna.
Show/hide table
Illustration 2 g03738277 - If necessary, follow Step 5.a through Step 5.c to remove soot antenna monitor (4). Refer to the Original Equipment Manufacture (OEM) for the correct location of soot antenna monitor.
- If necessary, use a suitable tool to disconnect harness assemblies (3) from the soot antennas.
- Disconnect the OEM harness assembly (6) from soot antenna monitor (4).
- Remove bolts (5) from soot antenna monitor (4). Remove the soot antenna monitor from the bracket.
Show/hide table
| |
| Illustration 1 | g03728597 |
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | - | Bostik Pure Nickel Anti-Seize Compound |
1 |
| B | - | 19 mm Crows Foot | 1 |
- Ensure that all components are clean and free from wear and damage. If necessary, replace any components that are worn or damaged.
Show/hide table
Illustration 3 g03738277 - If necessary, follow Step 2.a through Step 2.c to install soot antenna monitor (4). Refer to the OEM for the correct location of soot antenna monitor.
- Install soot antenna monitor (4) onto the bracket. Install bolts (5) to the soot antenna monitor. Tighten the bolts to a torque of
12 N·m (106 lb in) . - Connect the OEM harness assembly (6) to soot antenna monitor (4).
- If necessary, connect harness assemblies (3) to the soot antennas. Tighten the connection for the harness assemblies to a torque of
1.2 N·m (11 lb in) .
Show/hide table
Illustration 4 g03728597 - Install soot antenna monitor (4) onto the bracket. Install bolts (5) to the soot antenna monitor. Tighten the bolts to a torque of
- If new soot antennas are to be install, the protective cover on the new soot antenna will need to be removed prior to installation.
- Lightly lubricate the thread of soot antenna (2) with Tooling (A). Install soot antenna (2) to CEM (1).
- Use Tooling (B) to tighten soot antenna (2) to a torque of
45 N·m (33 lb ft) . - Repeat Step 3 to install the remaining soot antenna.
- Connect harness assembly (3) to soot antenna (2). Use a suitable tool to tighten the harness assembly to a torque of
1.2 N·m (11 lb in) . - Repeat Step 7 to connect the remaining harness assembly.
Caterpillar Information System:
325F Excavator Engine Supplement Electronic Control Module - Remove and Install
538 Forest Machine Machine Systems Specifications
303.5E2 CR Mini-HEX Machine ECM Electrical Power Supply - Test
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System CAN Data Link - Test
Wiper Arm May Interfere with Boom Tube Clamp on Certain Mini Hydraulic Excavators {5057} Wiper Arm May Interfere with Boom Tube Clamp on Certain Mini Hydraulic Excavators {5057}
303.5E2 CR Mini-HEX Machine ECM CAN Data Link - Test
XQP1100 Generator Set Engine Stopping
325F Excavator Engine Supplement Fan and Fan Drive - Remove and Install
An Improved Bucket Pin is Now Used on Certain 312D/D2 and 313D/D2 Excavators {6513} An Improved Bucket Pin is Now Used on Certain 312D/D2 and 313D/D2 Excavators {6513}
XQP150 Rental Generator Set Engine Starting
336D2/336D2 GC Excavator Engine Supplement Engine - Remove and Install
336D2/336D2 GC Excavator Engine Supplement Engine Front Mount - Remove and Install
340F Excavator Declaration of Conformity
Oil Leakage After Main Pump Shaft Seal Replacement {0663, 5070} Oil Leakage After Main Pump Shaft Seal Replacement {0663, 5070}
M314F, M316F, M318F, M320F and M322F Wheeled Excavator and Material Handler Machine Systems Piston Pump (Main Hydraulic) - Disassemble
Field Assembly Procedure for Dragline Buckets {6001, 7960} Field Assembly Procedure for Dragline Buckets {6001, 7960}
An Improved Assembly Procedure for Hammer Power Group Is Now Available for Certain H55E and H55ES Hydraulic Hammers {5077, 6333, 7555} An Improved Assembly Procedure for Hammer Power Group Is Now Available for Certain H55E and H55ES Hydraulic Hammers {5077, 6333, 7555}
New Pressure Sensor Gp Is Now Available for Certain Cat® Products {1000, 1408, 1439, 1718, 1906, 1924} New Pressure Sensor Gp Is Now Available for Certain Cat® Products {1000, 1408, 1439, 1718, 1906, 1924}
374F Excavator Restricted Visibility
814K Wheel Dozer Fuel System - Prime
815K Soil Compactor Bottom Guard Lowering
325F Excavator Engine Supplement Soot Sensor - Remove and Install
New Improved Oil Gauge Group Is Now Available On Certain Excavator Machine Engines {1326} New Improved Oil Gauge Group Is Now Available On Certain Excavator Machine Engines {1326}
303.5E2 CR Mini-HEX Machine ECM Sensor Signal (Analog, Passive) - Test