Spacer Plate - Remove and Install
Removal Procedure
Start By:
- Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Remove".
- Remove water seals (1) from the spacer plate.
Show/hide table
Illustration 1 | g00794042 |
- Install six 3/8-16 NC forcing screws (2) in the spacer plate (5). Tighten the screws evenly until the spacer plate is free from the dowels. Remove the gasket for the spacer plate.
Show/hide table
Illustration 2 | g00794086 |
- Remove the O-rings from location (3) and location (4) .
Installation Procedure
- Make sure that the spacer plate and the machined surface of the cylinder block are clean and free of dirt and foreign material.
- Put a new gasket (6) over the dowels on the cylinder block. Install O-ring seals (3) and (4) on the cylinder block.
Show/hide table
Illustration 3 | g00794124 |
- Install spacer plate (5) .
Show/hide table
Illustration 4 | g00794135 |
- Install new water seals (1) .
Show/hide table
Illustration 5 | g00794042 |
- Check the cylinder liner projection. Refer to Testing and Adjusting, "Cylinder Liners".
End By: Install the cylinder head.
Caterpillar Information System:
3412C Engine Fuel Injection Pump - Remove
3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Control Panel Configuration
Electronic Modular Control Panel II+ (EMCP II+) Starting Motor Remains Engaged (for MUI Engines)
C-10 and C-12 Industrial Engines Fuel Transfer Pump
Electronic Modular Control Panel II+ (EMCP II+) Fault Identification
Electronic Modular Control Panel II+ (EMCP II+) Service Tools
G3600 Engines Control Panel
Electronic Modular Control Panel II+ (EMCP II+) General Information
C-9 Industrial Engine E100 Low Engine Oil Pressure Warning
C-9 Industrial Engine E040 Low Engine Oil Pressure Shutdown
C-9 Industrial Engine E039 Low Engine Oil Pressure Derate
3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Control Panel Shutdown Mode
Electronic Modular Control Panel II+ (EMCP II+) Engine Does Not Shutdown (for EUI Engines)
3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Control Panel Programmable Logic Controller
2001/05/01 Corrections to Specifications Module, SENR3863-01, "G3406 Engine" {1102}
Electronic Modular Control Panel II+ (EMCP II+) Engine Does Not Shutdown (for MUI Engines)
3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Control Panel Setpoints
Electronic Modular Control Panel II+ (EMCP II+) GSC Operation Is Erratic
Electronic Modular Control Panel II+ (EMCP II+) Indicators of Alarm Module or Remote Annunciator Are Constantly Flashing
Electronic Modular Control Panel II+ (EMCP II+) Troubleshooting Diagnostic Codes
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 0100 - FMI 02 (for EUI Engines)
3412C Engine Automatic Timing Advance - Remove
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 0100 - FMI 02 (for MUI and PEEC Engines)
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 0100 - FMI 03