E100 Low Engine Oil Pressure Warning
产生此代码的情况:
Show/hide table
图 1 | g00784705 |
机油压力图 |
Show/hide table
触发水平     | 设定点(秒)     | 复位水平     | 复位时间     |
更多有关信息,请参看图1。     | 2 秒钟(sec)     | 70 kPa (10 psi)     |
20 秒钟     |
直到发动机转速已经连续30秒钟超过0 rpm 时,ECM才将作出反应动作。
系统响应:
出现活动"警告"事件时,报警灯将会点亮。
ECM将会在卡特(CAT)数据链路上产生EID 100诊断编码。 此诊断编码将会在电子技师(ET)的诊断屏幕(diagnostic screen)显示。
ECM将会在J1939数据链路上产生SPN 100-FMI 01诊断编码。 此诊断编码可在支持J1939数据链路的接收装置(receiving device)上显示。
ECM将会产生通过诊断灯显示的46闪烁编码。
- 发动机润滑系统可能有问题。
测试步骤 1. 检查有无诊断编码。
- 将卡特(Cat) ET与维修工具接头相连接。
- 把钥匙开关转到通电(ON)位置。 发动机应处于停机状态。
- 检查有无任何活动或记录诊断编码。
预期结果:
应没有任何诊断编码出现。
结果:
- 合格 - 进行测试步骤2。
- 不合格 -
修复: 修理出现的诊断编码。 请参阅本手册"有故障编码出现时的故障诊断与排除"部分中的适当专题。确保修理后故障被排除。
停止
测试步骤 2. 对发动机润滑系统进行检查。
- 对发动机润滑系统进行检查。 请参阅故障诊断与排除, "发动机机油压力低"。
预期结果:
发动机机油压力没问题。
结果:
- 合格 - 可能存在间歇性故障。
修复: 监视发动机的操作。修理故障。确保修理后故障被排除。
停止
- 不合格 -
修复: 修理故障。确保修理后故障被排除。
停止
Caterpillar Information System:
C-9 Industrial Engine E040 Low Engine Oil Pressure Shutdown
C-9 Industrial Engine E039 Low Engine Oil Pressure Derate
3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Control Panel Shutdown Mode
Electronic Modular Control Panel II+ (EMCP II+) SP Fault Codes
3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Control Panel Alarm Mode
G3516B Engines E042 Low System Voltage Shutdown
3034 Marine Engine Cooling System Coolant (ELC) - Change
Electronic Modular Control Panel II+ (EMCP II+) AL Fault Codes
Electronic Modular Control Panel II+ (EMCP II+) Fault Description
G3408C and G3412C Engines Engine Balancer - Remove and Install
Electronic Modular Control Panel II+ (EMCP II+) Alarm Mode
Electronic Modular Control Panel II+ (EMCP II+) Hourmeter Programming OP7
Electronic Modular Control Panel II+ (EMCP II+) General Information
G3600 Engines Control Panel
Electronic Modular Control Panel II+ (EMCP II+) Service Tools
Electronic Modular Control Panel II+ (EMCP II+) Fault Identification
C-10 and C-12 Industrial Engines Fuel Transfer Pump
Electronic Modular Control Panel II+ (EMCP II+) Starting Motor Remains Engaged (for MUI Engines)
3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Control Panel Configuration
3412C Engine Fuel Injection Pump - Remove
3412C Engine Spacer Plate - Remove and Install
Electronic Modular Control Panel II+ (EMCP II+) Engine Does Not Shutdown (for EUI Engines)
3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Control Panel Programmable Logic Controller
2001/05/01 Corrections to Specifications Module, SENR3863-01, "G3406 Engine" {1102}