Fault Identification
Show/hide table
Fault Identification     | ||||
Indicator left side of GSC+     |
Fault Code on upper display     | DIAG Indicator     | Fault Type     | See Topic     |
Fault Alarm     | CID FMI (1)     | Flashing     | Active Alarm     | Troubleshooting Diagnostic Codes     |
SP1, SP2, SP3, SP4 (1) | Absent     | Active Alarm     | Diagnostic System Procedures, "SP Fault Code"     | |
AL1 thru AL15 (1) | Absent     | Active Alarm     | Diagnostic System Procedures, "AL Fault Code"     | |
Fault Shutdown     | CID FMI     | Flashing     | Active Shutdown     | Troubleshooting Diagnostic Codes     |
SP1, SP2, SP3, SP4 | Absent     | Active Shutdown     | Diagnostic System Procedures, "SP Fault Code"     | |
AL5 thru AL15 (1) | Absent     | Active Alarm     | Diagnostic System Procedures, "AL Fault Code"     | |
Dedicated Shutdown:     |     | |||
Flashing     | Absent     | Absent     | Active Alarm     | Troubleshooting Dedicated Shutdown Indicators     |
On Continuously     | Absent     | Absent     | Active Shutdown     | |
None     | CID FMI (2)     | On Continuously     | Inactive Alarm     | Troubleshooting Diagnostic Codes     |
CID FMI (2) | On Continuously     | Inactive Shutdown     | Troubleshooting Diagnostic Codes     | |
SP1, SP2, SP3, SP4 | Absent     | Inactive Shutdown     | Diagnostic System Procedures, "SP Fault Code"     | |
AL5 through AL15 (1) | Absent     | Inactive Alarm     | Diagnostic System Procedures, "AL Fault Code"     | |
Absent | Absent     | Undiagnosed Shutdown     | Symptom Procedures     |
Show/hide table
( 1 ) | Fault code is shown after alarm codes key is pressed. |
( 2 ) | Fault Code is stored in the fault log of the GSC+. To view the fault code, see Systems Operation, "Fault Log Viewing OP1" within the topic Service Mode. |
Show/hide table
Illustration 1 | g00614724 |
GSC+ Display Area (1) Dedicated shutdown indicators (2) Spare fault indicators (3) Fault shutdown indicator (4) Fault alarm indicator (5) Upper display (6) Lower display (7) Keypad (8) DIAG indicator |
Faults that are detected and diagnosed by the GSC+ are shown to service personnel in the display area of the GSC+. The GSC+ uses dedicated shutdown indicators (1), fault shutdown indicator (3), fault alarm indicator (4), "DIAG" indicator (8), upper display (5) and lower display (6) to tell service personnel about a fault. Perform the following procedure in order to identify the fault that is detected by the GSC+.
Note: The "DIAG" indicator (8) functions when diagnostic information is available from the GSC+.
- Make a note of the indicators that are functioning on the left side of the "GSC+".
- View the fault code on the upper display (5). If the fault alarm indicator (4) is FLASHING and no fault code is present on the upper display (5), press the alarm codes key in order to view the fault code.
- Make a note of whether or not "DIAG" indicator (8) is FLASHING ON CONTINUOUSLY or ABSENT.
- On the fault identification chart, look at the first column. Locate the fault indicator that is functioning.
- Go to the second column in the chart. Find the fault code that is presently shown on the upper display (5) .
- Go to the third column in the chart which describes the status of "DIAG" indicator (8) .
- Read the last two columns in order to find the type of fault and corresponding topic within this module.
Caterpillar Information System:
Electronic Modular Control Panel II+ (EMCP II+) Service Tools
G3600 Engines Control Panel
Electronic Modular Control Panel II+ (EMCP II+) General Information
C-9 Industrial Engine E100 Low Engine Oil Pressure Warning
C-9 Industrial Engine E040 Low Engine Oil Pressure Shutdown
C-9 Industrial Engine E039 Low Engine Oil Pressure Derate
3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Control Panel Shutdown Mode
Electronic Modular Control Panel II+ (EMCP II+) SP Fault Codes
3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Control Panel Alarm Mode
G3516B Engines E042 Low System Voltage Shutdown
3034 Marine Engine Cooling System Coolant (ELC) - Change
Electronic Modular Control Panel II+ (EMCP II+) AL Fault Codes
C-10 and C-12 Industrial Engines Fuel Transfer Pump
Electronic Modular Control Panel II+ (EMCP II+) Starting Motor Remains Engaged (for MUI Engines)
3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Control Panel Configuration
3412C Engine Fuel Injection Pump - Remove
3412C Engine Spacer Plate - Remove and Install
Electronic Modular Control Panel II+ (EMCP II+) Engine Does Not Shutdown (for EUI Engines)
3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Control Panel Programmable Logic Controller
2001/05/01 Corrections to Specifications Module, SENR3863-01, "G3406 Engine" {1102}
Electronic Modular Control Panel II+ (EMCP II+) Engine Does Not Shutdown (for MUI Engines)
3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Control Panel Setpoints
Electronic Modular Control Panel II+ (EMCP II+) GSC Operation Is Erratic
Electronic Modular Control Panel II+ (EMCP II+) Indicators of Alarm Module or Remote Annunciator Are Constantly Flashing