Main Control Valve - Assemble - Attachment, Bucket, and Boom
组装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 1P-1862     | 钳     | 1     |
注: 检查 O 形密封圈、垫片和密封件有无磨损或损坏。 如有必要,请更换部件。
- 安装螺塞和 O 形密封圈 (80) 。
Show/hide table
图 1 | g00854185 |
- 组装分解器 (71) 。 将球 (73) 安装在阀 (74) 内。 安装阀座 (72) 。 安装支承环 (76) 和 (79) 。 安装 O 形密封圈 (75) 、 (77) 和 (78) 。
注: 将阀座 (72) 冷却后再将其插入阀 (74) 的孔内。
Show/hide table
图 2 | g00854173 |
- 安装分解器 (71) 。 拧紧分解器 (71) 至扭矩为50 ± 10 N·m (37 ± 7 lb ft)。 安装杆 (68) 、 (69) 和 (70) 。 安装螺塞和 O 形密封圈 (67) 。
Show/hide table
图 3 | g00854162 |
- 安装 O 形密封圈 (66) 。 安装螺塞 (65) 和 O 形密封圈。
Show/hide table
图 4 | g00854153 |
- 定位盖 (64) ,然后安装螺栓 (63) 。
Show/hide table
图 5 | g00854149 |
- 组装分解器阀 (57) 。 安装支承环 (59) 和 (60) 。 安装 O 形密封圈 (58) 、 (61) 和 (62) 。
Show/hide table
图 6 | g00854122 |
- 安装螺塞和 O 形密封圈 (56) 。 安装分解器阀 (57) 。 拧紧分解器阀 (57) 至扭矩为50 ± 10 N·m (37 ± 7 lb ft)。
Show/hide table
图 7 | g00854098 |
- 将 O 形密封圈 (51) 、隔套 (52) 、弹簧 (53) 和阀 (54) 安装到阀体 (55) 中。 安装螺塞 (50) 。
Show/hide table
图 8 | g00854070 |
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
- 安装支承环 (45) 和 (48) 。 安装 O 形密封圈 (46) 、 (47) 和 (49) 。
Show/hide table
图 9 | g00854005 |
- 安装差动阀 (44) 。 拧紧差动阀 (44) 至扭矩为 235 ± 10 N·m (173 ± 7 lb ft)。
Show/hide table
图 10 | g00853986 |
- 组装所有电磁阀组件。 安装弹簧 (40) 、 (41) 和 (42) 。 安装护圈 (43) 。
Show/hide table
图 11 | g00853964 |
- 使用工具 (A) 安装挡圈 (39) 。
Show/hide table
图 12 | g00853948 |
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
- 安装 O 形密封圈 (37) 和 (38) 。
Show/hide table
图 13 | g00853913 |
- 安装阀 (33) 、弹簧 (34) 、O 形密封圈 (35) 和电磁阀 (36) 。
Show/hide table
图 14 | g00853771 |
- 安装螺栓 (32) 。
Show/hide table
图 15 | g00853770 |
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
- 安装活塞 (29) 。 安装螺塞和 O 形密封圈 (30) 。 安装 O 形密封圈 (28) 和 (31) 。 安装隔套 (19) 。
Show/hide table
图 16 | g00853768 |
- 使用适当的起吊设备定位执行器总成 (26) 并安装螺栓 (27) 。 执行器总成 (26) 的重量约为 28 kg (60 lb)。 安置支架组件 (24) 并安装螺栓 (25) 。
Show/hide table
图 17 | g00853767 |
- 安装隔套 (19) 。 使用适当的起吊设备定位执行器总成 (23) 并安装螺栓 (21) 。 执行器总成 (23) 的重量约为 28 kg (60 lb)。 安置支架组件 (20) 并安装螺栓 (22) 。
Show/hide table
图 18 | g00853766 |
- 安装支承环 (12) 和 (16) 。 安装 O 形密封圈 (13) 、 (14) 、 (15) 、 (17) 和 (18) 。 组装管路安全阀 (10) 和 (11) 。 拧紧螺母 (17A) 至扭矩为 80 ± 10 N·m (59 ± 7 lb ft)。 拧紧螺母 (18A) 至扭矩为 33 ± 5 N·m (24 ± 4 lb ft)。
Show/hide table
图 19 | g00856084 |
- 安装管路安全阀 (11) 。 拧紧管路安全阀 (11) 至扭矩为 300 ± 40 N·m (220 ± 30 lb ft)。
Show/hide table
图 20 | g00853764 |
- 安装管路安全阀 (10) 。 拧紧管路安全阀 (10) 至扭矩为 300 ± 40 N·m (220 ± 30 lb ft)。
Show/hide table
图 21 | g00853763 |
- 组装流量补偿器阀。 安装弹簧 (6) 、套筒 (7) 、弹簧 (8) 和阀 (9) 。
Show/hide table
图 22 | g00853762 |
- 安装流量补偿器阀 (5) 。
Show/hide table
图 23 | g00853760 |
- 安装 O 形密封圈 (3) 和 (4) 。
Show/hide table
图 24 | g00853761 |
- 定位盖 (2) ,然后安装螺栓 (1) 。
Show/hide table
图 25 | g00853759 |
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
Caterpillar Information System:
365C Excavator Machine Systems Main Control Valve - Disassemble - Attachment, Bucket, and Boom
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Crankshaft Vibration Damper and Pulley - Remove
PP120 and PH126 Power Pack and Hammer Work Tool Troubleshooting
302.5C Mini Hydraulic Excavator Machine Systems Solenoid Valve (Travel Speed) - Remove and Install
302.5C Mini Hydraulic Excavator Machine Systems Solenoid Valve (Auxiliary Circuit) - Remove and Install
PP120 and PH126 Power Pack and Hammer Engine Speed Control Cylinder
365C Excavator Machine Systems Boom Cylinder - Remove and Install
365C Excavator Machine Systems Stick Cylinder - Remove and Install
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Water Pump - Install
302.5C Mini Hydraulic Excavator Machine Systems Relief Valve (Pilot) - Remove and Install
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Solenoid Valve (Auxiliary Circuit) - Assemble - 1-Way/2-Way Flow
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Solenoid Valve (Auxiliary Circuit) - Disassemble - 1-Way/2-Way Flow
365C Excavator Machine Systems Main Control Valve - Disassemble - Proportional Valve
365C Excavator Machine Systems Main Control Valve - Assemble - Proportional Valve
365C Excavator Machine Systems Main Control Valve - Disassemble - Manifold Valve
365C Excavator Machine Systems Main Control Valve - Assemble - Manifold Valve
365C Excavator Machine Systems Main Control Valve - Disassemble - Right Travel, Left Travel, and Stick
365C Excavator Machine Systems Main Control Valve - Assemble - Right Travel, Left Travel, and Stick
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Counterbalance Valve (Travel) - Remove
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Counterbalance Valve (Travel) - Install
725C2, 730C2 Ejector Articulated Trucks - Machine Systems Ejector Cylinder - Disassemble - Three Stage Cylinder and Four Stage Cylinder
725C2, 730C2 Ejector Articulated Trucks - Machine Systems Ejector Cylinder - Assemble - Three Stage Cylinder and Four Stage Cylinder
345C MHPU Mobile Hydraulic Power Unit Machine Systems Swing Drive - Remove
345C MHPU Mobile Hydraulic Power Unit Machine Systems Swing Drive - Install