Solenoid Valve (Auxiliary Circuit) - Assemble - 1-Way/2-Way Flow
Assembly Procedure
- Lubricate all bores with the lubricant that is being sealed. Install filter (17), collar (18), and retaining ring (19). Install O-ring seals (16) on adapter (13). Install valve (15), spring (14), and adapter (13). Tighten adapter (13) to a torque of 146 ± 15 N·m (108 ± 11 lb ft).
Show/hide table
Illustration 1 | g01196593 |
Show/hide table
Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment. |
Note: Install filter (17) from the caulked side of filter (17) .
- Install backup ring (11), O-ring seal (12), and seat (10). Install retainer (9). Tighten retainer (9) to a torque of 30 ± 3 N·m (22 ± 2 lb ft). Install valve (8). Install retaining ring (7) .
Show/hide table
Illustration 2 | g01196592 |
- Install O-ring seal (3) and shims (4). Install coil (2) and bolts (1). Tighten bolts (1) to a torque of 2.25 ± 0.25 N·m (20 ± 2 lb in). Install O-ring seals (6) on valve group (5) .
Show/hide table
Illustration 3 | g01196591 |
End By: Install the solenoid valve. Refer to Disassembly and Assembly, "Solenoid Valve (Auxiliary Circuit) 1-Way/2-Way Flow (Left) - Install".
Caterpillar Information System:
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Solenoid Valve (Auxiliary Circuit) - Disassemble - 1-Way/2-Way Flow
Installation of 173-2190 Work Tool Wiring Gp (KIT) for Broom Operation {1408, 6702, 6708, 7000} Installation of 173-2190 Work Tool Wiring Gp (KIT) for Broom Operation {1408, 6702, 6708, 7000}
C15 Petroleum Generator Set Engines Fuel Filter Base
3508 and 3516 EUI Engines for 5130 and 5230 Excavators Camshaft
3508 and 3516 EUI Engines for 5130 and 5230 Excavators Crankshaft
3508 EUI Engines Camshaft
3508 EUI Engines Crankshaft
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Solenoid Valve (Auxiliary Circuit) - Install - 1-Way/2-Way, Flow (Left)
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Solenoid Valve (Auxiliary Circuit) - Remove - 1-Way/2-Way, Flow (Left)
PP120 and PH126 Power Pack and Hammer Safety Messages
365C Excavator Machine Systems Boom - Install
365C Excavator Machine Systems Boom - Remove
302.5C Mini Hydraulic Excavator Machine Systems Relief Valve (Pilot) - Remove and Install
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Water Pump - Install
365C Excavator Machine Systems Stick Cylinder - Remove and Install
365C Excavator Machine Systems Boom Cylinder - Remove and Install
PP120 and PH126 Power Pack and Hammer Engine Speed Control Cylinder
302.5C Mini Hydraulic Excavator Machine Systems Solenoid Valve (Auxiliary Circuit) - Remove and Install
302.5C Mini Hydraulic Excavator Machine Systems Solenoid Valve (Travel Speed) - Remove and Install
PP120 and PH126 Power Pack and Hammer Work Tool Troubleshooting
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Crankshaft Vibration Damper and Pulley - Remove
365C Excavator Machine Systems Main Control Valve - Disassemble - Attachment, Bucket, and Boom
365C Excavator Machine Systems Main Control Valve - Assemble - Attachment, Bucket, and Boom
365C Excavator Machine Systems Main Control Valve - Disassemble - Proportional Valve