Boom - Install
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
B     | 4C-6486     | 台架     | 1     |
8S-8048 | 鞍座     | 1     | |
8S-7641 | 管组件     | 1     | |
8S-7615 | 销     | 1     | |
C     | 189-0863     | 钩环组件     | 2     |
E     | 276-8834     | 销冲头盖     | 1     |
- 使用工具 (C) 和适当的起吊设备将动臂 (9) 安置在机架中。 对准动臂 (9) 和机架上的孔。 动臂 (9) 和斗杆油缸的组合重量约为 6124 kg (13500 lb)。
Show/hide table
图 1 | g01196497 |
注: 安装动臂前,确保彻底清洁动臂和机架上的孔。
- 将动臂滑动至一侧,使动臂与机架接触。 在安装销孔测量动臂和机架之间的间隙 (Z) 。 此间隙不得大于 1.0 mm (0.04 in)。 如果此间隙小于 1.0 mm (0.04 in),则不需添加垫片。 如果此间隙大于 1.0 mm (0.04 in),请添加正确厚度的垫片以便获得所需的间隙。
Show/hide table
图 2 | g00879638 |
(X) 上部机架 (Y) 动臂 |
- 如有必要,在动臂和机架之间安装垫片。 使用适当的起吊设备安置销组件 (10) 。 使用工具 (E) 和适当的锤子安装销组件 (10) 。 销组件 (10) 的重量约为 109 kg (240 lb)。
Show/hide table
图 3 | g01196530 |
- 将螺栓 (11) 安装到销组件 (10) 中。
Show/hide table
图 4 | g01196540 |
- 对其他销组件重复步骤 2 至 4。 将工具 (C) 从动臂上拆下。
- 连接软管组件 (8) 。
Show/hide table
图 5 | g01196492 |
- 安装夹子 (7) ,然后连接线束组件 (6) 。
- 滑动动臂油缸支撑销,使动臂油缸支撑销与动臂平齐。
- 利用适当的起吊设备将动臂油缸 (4) 提升到位。 将动臂油缸 (4) 连杆端与动臂油缸支撑销对准。 拆下工具 (B) 。
Show/hide table
图 6 | g00570755 |
- 使用工具 (E) 和适当的锤子安装动臂油缸支撑销。
Show/hide table
图 7 | g01196549 |
- 重复步骤 9 和 10 以连接其他动臂油缸。
- 安装隔套和挡板 (3) 。 安装螺栓 (2) 。
Show/hide table
图 8 | g00591906 |
- 重复步骤 12 以将挡板安装在相对的动臂油缸上。
- 连接润滑脂软管组件 (1) 。
Show/hide table
图 9 | g00574959 |
- 润滑动臂油缸安装销。 有关正确的步骤,请参阅操作和保养手册。
End By: 安装斗杆。 请参阅 拆解和组装, "斗杆 - 安装"。
Caterpillar Information System:
365C Excavator Machine Systems Boom - Remove
365C Excavator Machine Systems Boom Bearings and Seals - Remove and Install
365C Excavator Machine Systems Stick - Install
365C Excavator Machine Systems Stick - Remove
365C Excavator Machine Systems Stick Bearings and Seals - Remove and Install
C7 Engine for AP-1000D, AP-1055D, BG-2455D, and BG-260D Asphalt Pavers Engine Will Not Crank
PP120 and PH126 Power Pack and Hammer Engine
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Water Pump - Remove
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Solenoid Valve (Auxiliary Circuit) - Install - 1-Way/2-Way, Check (Left)
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Solenoid Valve (Auxiliary Circuit) - Remove - 1-Way/2-Way, Check (Left)
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Fan - Install
320D Forest Machine Machine System Specifications Main Hydraulic Pump - Auxiliary Pump
PP120 and PH126 Power Pack and Hammer Safety Messages
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Solenoid Valve (Auxiliary Circuit) - Remove - 1-Way/2-Way, Flow (Left)
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Solenoid Valve (Auxiliary Circuit) - Install - 1-Way/2-Way, Flow (Left)
3508 EUI Engines Crankshaft
3508 EUI Engines Camshaft
3508 and 3516 EUI Engines for 5130 and 5230 Excavators Crankshaft
3508 and 3516 EUI Engines for 5130 and 5230 Excavators Camshaft
C15 Petroleum Generator Set Engines Fuel Filter Base
Installation of 173-2190 Work Tool Wiring Gp (KIT) for Broom Operation {1408, 6702, 6708, 7000} Installation of 173-2190 Work Tool Wiring Gp (KIT) for Broom Operation {1408, 6702, 6708, 7000}
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Solenoid Valve (Auxiliary Circuit) - Disassemble - 1-Way/2-Way Flow
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Solenoid Valve (Auxiliary Circuit) - Assemble - 1-Way/2-Way Flow
302.5C Mini Hydraulic Excavator Machine Systems Relief Valve (Pilot) - Remove and Install