Fuel Priming Pump - Remove and Install
Removal Procedure
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Move the battery disconnect switch to the OFF position.
- Open the access door in the center of the hood.
- Move the fuel shutoff valve to the OFF position. Refer to Operation and Maintenance Manual, "Fuel Tank Shutoff and Drain Control".
- Remove bolts (1). Remove fuel priming pump (2) .
Show/hide table
 | |
| Illustration 1 | g01194416 |
- Remove the O-ring seal from fuel priming pump (2) .
Installation Procedure
- Install the new O-ring seal into fuel priming pump (2) .
- Position fuel priming pump (2). Install bolts (1) .
Show/hide table
| | |
| Illustration 2 | g01194416 |
- Move the fuel shutoff valve to the ON position. Refer to Operation and Maintenance Manual, "Fuel Tank Shutoff and Drain Control".
- Close the access door in the center of the hood.
- Move the battery disconnect switch to the ON position.
Caterpillar Information System:
302.5C Mini Hydraulic Excavator Machine Systems Solenoid Valve (Hydraulic Lockout) - Remove and Install
PP120 and PH126 Power Pack and Hammer Plate Locations and Film Locations
3406C Engines for Caterpillar Built Machines Engine Oil Pump
301.6C and 301.8C Mini Hydraulic Excavators Machine Systems Upper Frame and Undercarriage Frame - Connect
302.5C Mini Hydraulic Excavator Machine Systems Accumulator (Hydraulic Pilot) - Remove and Install
PP120 and PH126 Power Pack and Hammer Approved Work Tools
PP120 and PH126 Power Pack and Hammer Specifications
PP120 and PH126 Power Pack and Hammer Operation
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Cylinder Head - Install - In-Chassis
C13, C15, and C18 Tier 4 Final Engines Electric Starting Motor
325D and 329D Excavators and 325D Material Handler Machine System Specifications Pump Coupling
S320B, S325B, S340B, S365B and S385B Demolition Shears Hydraulic Rotator and Shear Housing - Separate
303C CR, 303.5C CR, 304C CR and 305C CR Mini Hydraulic Excavators Work Tool Control
C7 and C9 Engines for Caterpillar Built Machines Sensors and Electrical Connectors
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Fuel Transfer Pump - Remove and Install
C7.1 Engines for Caterpillar Built Machines Flywheel Housing
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Fuel Filter (Primary) and Fuel Filter Base - Remove and Install
416E Backhoe Loader Backhoe Boom, Stick, Bucket, and Cylinder Bearings - Lubricate
301.6C and 301.8C Mini Hydraulic Excavators Machine Systems Boom - Remove and Install
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Fuel Filter and Water Separator Base - Remove and Install
2005/08/22 Lubrication Procedure for the Master Links in the Track {4169}
303C CR, 303.5C CR, 304C CR and 305C CR Mini Hydraulic Excavators Monitoring System
M318C and M322C Excavators Machine Systems Control Valve (Medium Pressure) - Disassemble - Joystick Steering
M318C and M322C Excavators Machine Systems Control Valve (Medium Pressure) - Assemble - Joystick Steering