Control Valve (Medium Pressure) - Assemble - Joystick Steering
Assembly Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 246-9300     | Pin Socket     | 1     |
- Install check valve (25). Tighten check valve (25) to a torque of 8 N·m (71 lb in). Use Tooling (A) to install check valve (24). Tighten check valve (24) to a torque of 3 N·m (27 lb in). Install fitting (23). Repeat for the remaining fittings and check valves.
Show/hide table
Illustration 1 | g01194734 |
Show/hide table
Illustration 2 | g01194735 |
Show/hide table
Illustration 3 | g01194736 |
- Install spools (20), (22), and (17). Install washers (21) and (16). Install O-ring seals (13) and (19). Install springs (14) and (18). Install covers (11) and (12). Tighten covers (11) and (12) to a torque of 90 N·m (66 lb ft). Install O-ring seals (15) .
Show/hide table
Illustration 4 | g01194733 |
Show/hide table
Illustration 5 | g01194732 |
Show/hide table
Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment. |
- Install O-ring seals (5) and (7) and backup rings (4) and (6). Install O-ring seals (8), (9), and (10) .
Show/hide table
Illustration 6 | g01194731 |
Show/hide table
Illustration 7 | g01194730 |
- Install cartridge assembly (1). Tighten cartridge assembly (1) to a torque of 30 N·m (22 lb ft). Install solenoid (2) and nut (3). Tighten nut (3) to a torque of 2.7 N·m (24 lb in).
- Repeat Steps 3 and 4 for the remaining solenoid valve.
End By: Install the control valve for joystick steering. Refer to Disassembly and Assembly, "Control Valve (Medium Pressure) - Install".
Caterpillar Information System:
M318C and M322C Excavators Machine Systems Control Valve (Medium Pressure) - Disassemble - Joystick Steering
303C CR, 303.5C CR, 304C CR and 305C CR Mini Hydraulic Excavators Monitoring System
2005/08/22 Lubrication Procedure for the Master Links in the Track {4169}
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Fuel Filter and Water Separator Base - Remove and Install
301.6C and 301.8C Mini Hydraulic Excavators Machine Systems Boom - Remove and Install
416E Backhoe Loader Backhoe Boom, Stick, Bucket, and Cylinder Bearings - Lubricate
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Fuel Filter (Primary) and Fuel Filter Base - Remove and Install
C7.1 Engines for Caterpillar Built Machines Flywheel Housing
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Fuel Transfer Pump - Remove and Install
C7 and C9 Engines for Caterpillar Built Machines Sensors and Electrical Connectors
303C CR, 303.5C CR, 304C CR and 305C CR Mini Hydraulic Excavators Work Tool Control
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Fuel Priming Pump - Remove and Install
M318C and M322C Excavators Machine Systems Control Valve (Medium Pressure) - Disassemble
M318C and M322C Excavators Machine Systems Control Valve (Medium Pressure) - Assemble
320D, 321D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators, 324D Forest Machine and 323D MHPU, 324D MHPU, 325D MHPU, 329D MHPU, 330D MHPU and 336D MHPU Mobile Hydraulic Power Units Machine Electronic Control System Diagnostic Code List
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Hood - Remove and Install
PP120 and PH126 Power Pack and Hammer System Pressure - Release
PP120 and PH126 Power Pack and Hammer Work Tool Installation and Removal
Cast Pin Grabber Quick Coupler Specifications
Cast Pin Grabber Quick Coupler Approved Machines
Cast Pin Grabber Quick Coupler Rated Load
H140D S, H160D S and H180D S Hydraulic Hammers Control Valve
Cast Pin Grabber Quick Coupler Quick Coupler Installation and Removal
PP120 and PH126 Power Pack and Hammer Tool Selection