Water Pump - Disassemble
Disassembly Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 1P-0510     | Driver Group     | 1     |
B     | 1P-0520     | Driver Group     | 1     |
Start By:
- Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove O-ring seals (4) and (5) from cover plate (3). Inspect the O-ring seals for wear or damage. If the O-ring seals are worn or damaged, use new parts for replacement.
Show/hide table
Illustration 1 | g00743367 |
- Remove four bolts (2) that fasten cover plate (3) to water pump (1) .
- Remove cover plate (3) from water pump (1) .
- Remove hose nipple (6) and the O-ring seal from water pump (1). Inspect the O-ring seal for wear or damage. If the O-ring seal is worn or damaged, use a new part for replacement.
Show/hide table
Illustration 2 | g00743370 |
- Remove three bolts (7) and remove elbow (8) from water pump (1) .
- Remove O-ring seal (9) from elbow (8). Inspect the O-ring seal for wear or damage. If the O-ring seal is worn or damaged, use a new part for replacement.
Show/hide table
Illustration 3 | g00743372 |
- Position the water pump in a press. Use spacer plates to level the water pump.
Show/hide table
Illustration 4 | g00743374 |
- Use a suitable drive plate from Tool (A) and a press in order to push the shaft out of impeller (10). Remove impeller (10) from the water pump.
- Continue to push the shaft out of seal (11) and the water pump housing.
Show/hide table
Illustration 5 | g00743376 |
Note: Do not allow the shaft to fall to the floor when the shaft is removed.
- Remove seal (11) from the water pump housing with the handle from Tool (B) and a press.
Show/hide table
Illustration 6 | g00645786 |
Caterpillar Information System:
3126B Marine Engine Water Temperature Regulator - Remove and Install
3054B Industrial Engine Water Outlet Manifold - Remove
Caterpillar Monitoring System for Electronic Modular Control Panel CID 0827 FMI 08 Temperature Sensor (Left Exhaust) Abnormal Signal - Test
G3412C, G3508, G3512, G3516, G3606, G3608, G3612 and G3616 Engines Customer Communication Module General Wiring Diagram
3612 and 3616 Engines Crankshaft Main Bearings - Install
3618 Engine Piston and Connecting Rods - Remove
3126B Marine Engine Water Pump - Install
3126 Truck Engine Military Air Inlet Heater - Remove and Install
3126B Marine Engine Water Pump - Remove
3612 and 3616 Engines Crankshaft - Remove
3618 Engine Piston Cooling Jets - Remove and Install
Customer Communication Module (CCM) for Diesel Engines Acronyms
3612 and 3616 Engines Crankshaft - Install
3054B Industrial Engine Water Outlet Manifold - Install
3618 Engine Piston and Connecting Rods - Install
3054B Industrial Engine Valve Mechanism Cover - Remove and Install
3054B Industrial Engine Fan Drive - Remove
3126B Marine Engine Engine Oil Cooler - Remove
3126B Marine Engine Engine Oil Cooler - Install
3054B Industrial Engine Fan Drive - Install
3512B Marine Auxiliary Engine Low Idle/High Idle Switch
SR4 HV and SR4B HV Generators Continuous Operation
SR4 HV and SR4B HV Generators Rotating Rectifier - Check
3512B Marine Auxiliary Engine Black Start Push Button