Radiator - Install
Installation Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 138-7574 | Link Bracket | 2 |
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide", for tools and supplies suitable to collect and contain fluids in Caterpillar machines. Dispose of all fluids according to local regulations and mandates. |
- Check the condition of the radiator prior to the installation. Remove any dirt or debris that may restrict the flow of air through the core. If any of the cooling fins are bent, the fins should be straightened.
- Fasten Tooling (A) and a suitable lifting device to radiator (5), as shown.
Show/hide table
 | |
| Illustration 1 | g00364578 |
- Carefully position the radiator on the machine, as shown. The weight of the radiator is 55 kg (120 lb).
- Install eight bolts (4) that hold the radiator to the support assembly.
- Connect the radiator overflow hose (3) .
- Connect radiator bottom hose (2). Tighten hose clamp (1) .
Show/hide table
 | |
| Illustration 2 | g00364577 |
- Connect the radiator top hose. Tighten the hose clamp on the radiator top hose.
- Fill the cooling system to the correct level. Refer to Operation and Maintenance Manual for the correct filling procedure.
End By:
- Install the hydraulic oil cooler. Refer to Disassembly and Assembly, "Hydraulic Oil Cooler - Install" in this manual.
- Install the fan. Refer to Disassembly and Assembly, "Fan - Remove and Install" in this manual.
- Install the hood. Refer to Disassembly and Assembly, "Hood - Remove and Install" in this manual.
Caterpillar Information System:
330B Excavator Hydraulic System Pump Control (Output Flow) - Adjust
315B Excavator Machine Systems Cab - Remove
M315 Excavator Machine System Bucket Cylinder
315B and 315B L Excavator Supplement For 3046 Engine Radiator - Remove
315B Excavator Machine Systems Seat - Remove and Install
5230 Excavator Hydraulic System Hydraulic System Troubleshooting
315B Excavator Machine Systems Fuel Tank - Install
315B Excavator Machine Systems Undercarriage Frame - Remove
5130B Excavator Hydraulic System Relief Valve (Margin)
M315 Excavator Machine System Stick - 3.1 m (10.17 ft)
M315 Excavator Machine System Stick - 2.6 m (8.53 ft)
M315 Excavator Machine System Stick - 2.4 m (7.87 ft)
330B Excavator Hydraulic System Swing Motor - Test - Measurement of Case Drain Oil
330B Excavator Hydraulic System Travel Motor - Test - Measurement of Case Drain Oil
315B and 315B L Excavator Supplement For 3046 Engine Coolant Tank (Expansion) - Remove and Install
5130 Excavator Hydraulic System Check Valve (Swing and Travel Back Pressure)
315B Excavator Machine Systems Cab - Install
M318 and M320 Excavators Machine System Specifications Control Valve (Boom Lowering)
330B Excavator Hydraulic System Gear Pump (Pilot) - Test
315B and 315B L Excavator Supplement For 3046 Engine Engine and Piston Pump - Remove
315B Excavator Machine Systems Track Carrier Roller - Disassemble
M315 Excavator Machine System Boom Cylinder
330B Excavator Hydraulic System Relief Valve (Swing) - Test and Adjust
M312 Excavator Machine System Bucket Sidecutter