Cab - Remove
Removal Procedure
- Open the cab door. Lock the cab door in the OPEN position.
- Remove three screws (1) and guard (2) .
Show/hide table
Illustration 1 | g00364712 |
- Remove rubber floormat (3) from the cab.
Show/hide table
Illustration 2 | g00364812 |
- Remove three screws (4) and cover (5) .
Show/hide table
Illustration 3 | g00364832 |
- Remove air duct (7) from elbow (6) .
Show/hide table
Illustration 4 | g00364837 |
- Remove four screws (8) from the cover at the rear of the cab.
Show/hide table
Illustration 5 | g00364838 |
- Open rear compartment door (9). Remove four screws (10) and cover (11) from the rear of the cab.
Show/hide table
Illustration 6 | g00364896 |
- Disconnect hose (12) from box (13) .
Show/hide table
Illustration 7 | g00364899 |
- Remove wiring harness (15) from the side of box (13) .
Show/hide table
Illustration 8 | g00364952 |
- Remove four screws (14) and box (13) from the rear of the cab.
- Remove two bolts (17), the washers and cover (16) from the rear of the cab.
Show/hide table
Illustration 9 | g00364978 |
- Disconnect electrical connectors (18) and (19) .
Show/hide table
Illustration 10 | g00364982 |
- Disconnect electrical connectors (20) and (21) .
Show/hide table
Illustration 11 | g00364983 |
- Remove nine bolts (22) and the washers that hold the cab to platform (23) .
Show/hide table
Illustration 12 | g00365052 |
- Fasten a hoist to the lifting bracket on top of cab (24), as shown. Carefully remove the cab from the platform. The weight of the cab is 288 kg (635 lb).
Show/hide table
NOTICE |
---|
Raise the cab slowly. Check for additional lines or connections that could be damaged. |
Show/hide table
Illustration 13 | g00480925 |
Caterpillar Information System:
M315 Excavator Machine System Bucket Cylinder
315B and 315B L Excavator Supplement For 3046 Engine Radiator - Remove
315B Excavator Machine Systems Seat - Remove and Install
5230 Excavator Hydraulic System Hydraulic System Troubleshooting
315B Excavator Machine Systems Fuel Tank - Install
315B Excavator Machine Systems Undercarriage Frame - Remove
5130B Excavator Hydraulic System Relief Valve (Margin)
M315 Excavator Machine System Stick - 3.1 m (10.17 ft)
M315 Excavator Machine System Stick - 2.6 m (8.53 ft)
M315 Excavator Machine System Stick - 2.4 m (7.87 ft)
M315 Excavator Machine System Stick - 2.1 m (6.89 ft)
320B, 320B L and 320B N Excavators Work Tool Flow Control - If Equipped
330B Excavator Hydraulic System Pump Control (Output Flow) - Adjust
315B and 315B L Excavator Supplement For 3046 Engine Radiator - Install
330B Excavator Hydraulic System Swing Motor - Test - Measurement of Case Drain Oil
330B Excavator Hydraulic System Travel Motor - Test - Measurement of Case Drain Oil
315B and 315B L Excavator Supplement For 3046 Engine Coolant Tank (Expansion) - Remove and Install
5130 Excavator Hydraulic System Check Valve (Swing and Travel Back Pressure)
315B Excavator Machine Systems Cab - Install
M318 and M320 Excavators Machine System Specifications Control Valve (Boom Lowering)
330B Excavator Hydraulic System Gear Pump (Pilot) - Test
315B and 315B L Excavator Supplement For 3046 Engine Engine and Piston Pump - Remove
315B Excavator Machine Systems Track Carrier Roller - Disassemble
M315 Excavator Machine System Boom Cylinder