S3015, S3025 and S3035 Demolition and Scrap Shears Caterpillar


Swivel - Remove

Usage:

S3025 LNS

Removal Procedure

Reference: Special Instruction, "Visual Service Procedures - Colors and Symbols" M0066576.

Table 1
Tools Required 
Tool  Part Number  Part Description  Qty 
4C-8359  Eyebolt 
Support bar (20 mm * 150 mm * 1000 mm) 

Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies to prevent fluid loss and to keep contaminants from entering the system.

Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned to prevent dirt from entering the internal mechanism.

------ WARNING! ------

Personal injury can result from hydraulic oil pressure and hot oil.

Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.

Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.

Dispose of all fluids according to local regulations and mandates.




Illustration 1g06341976


Illustration 2g06341977


Illustration 3g06341978


Illustration 4g06341979


Illustration 5g06341980


Illustration 6g06341982


Illustration 7g06342141


Illustration 8g06342144


Illustration 9g06342145


Illustration 10g06342146


Illustration 11g06342149


Illustration 12g06342151


Illustration 13g06342153

Caterpillar Information System:

Improved Thrust Washer and Wheel Bearing Retainer Are Now Used on Certain 824K Wheel Dozers and 826K Landfill Compactors {4051} Improved Thrust Washer and Wheel Bearing Retainer Are Now Used on Certain 824K Wheel Dozers and 826K Landfill Compactors {4051}
Coolant May Overflow During Engine Warm Up on Certain 785C and 789C Off-Highway Trucks {1070, 1380} Coolant May Overflow During Engine Warm Up on Certain 785C and 789C Off-Highway Trucks {1070, 1380}
24 Motor Graders Engine Supplement Engine Support (Rear) - Remove and Install
S3015, S3025 and S3035 Demolition and Scrap Shears Swivel - Remove
Hose Clamp Retention Information for 794 AC Off-Highway Truck has Changed {4257, 4304, 5057, 7510, 7540, 7554} Hose Clamp Retention Information for 794 AC Off-Highway Truck has Changed {4257, 4304, 5057, 7510, 7540, 7554}
24 Motor Grader Power Train Modulating Valve (Torque Converter Lockup Clutch) - Remove and Install
M315D2 and M317D2 Wheeled Excavators Prepare the Machine for Maintenance
789D CMD Off-Highway Truck Chassis Electronic Control System (Command For Hauling) Electronic Control Module (ECM) - Configure
789D CMD Off-Highway Truck Chassis Electronic Control System (Command For Hauling) Electronic Control Module (ECM) - Replace
789D CMD Off-Highway Truck Chassis Electronic Control System (Command For Hauling) Electronic Control Module (ECM) - Flash Program
789D CMD Off-Highway Truck Chassis Electronic Control System (Command For Hauling) Wiring Harness (Short Circuit) - Test
789D CMD Off-Highway Truck Chassis Electronic Control System (Command For Hauling) Wiring Harness (Open Circuit) - Test
789D and 789D XQ Off-Highway Trucks Pump Drive Shaft Universal Joint - Inspect
Repair Option for Shaft Assembly Spalling on Certain Integrated Toolcarriers, Wheel Loaders, and Wheel Skidders {3030, 3063, 3155, 3169, 3170} Repair Option for Shaft Assembly Spalling on Certain Integrated Toolcarriers, Wheel Loaders, and Wheel Skidders {3030, 3063, 3155, 3169, 3170}
S3015, S3025 and S3035 Demolition and Scrap Shears Gear and Bearing - Remove and Install
Cleaning Procedure of the Standard Pre-Cleaner Assembly on Certain 836K Landfill Compactors {1055} Cleaning Procedure of the Standard Pre-Cleaner Assembly on Certain 836K Landfill Compactors {1055}
785D Off-Highway Truck Pump Drive Shaft Universal Joint - Inspect
793D Off-Highway Truck Pump Drive Shaft Universal Joint - Inspect
793D Off-Highway Truck Main Drive Shaft Universal Joint - Inspect
S3015, S3025 and S3035 Demolition and Scrap Shears Swivel - Install
12M Series 3, 140M Series 3 and 160M Series 3 Motor Graders Piston Motor (Hydraulic Fan)
Autolube Lubrication Pump Inoperable On Certain Wheel Loaders {7540} Autolube Lubrication Pump Inoperable On Certain Wheel Loaders {7540}
Improved Hydraulic Oil Filter Bypass Indicator Is Now Available for Certain Cat Machines {5068} Improved Hydraulic Oil Filter Bypass Indicator Is Now Available for Certain Cat Machines {5068}
New Hose Assembly in the Hydraulic Lines Group Is Now Used on Certain 120M and 120M Series 2 Motor Graders {5057} New Hose Assembly in the Hydraulic Lines Group Is Now Used on Certain 120M and 120M Series 2 Motor Graders {5057}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.