Electric Starting Motor - Remove and Install
Show/hide table
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool. |
- Raise the engine hood.
- Turn the battery disconnect switch to the OFF position.
Show/hide table
Illustration 1 g03691329 - Remove panel (1).
Show/hide table
Illustration 2 g03691345 - Disconnect harness assemblies (2). Disconnect clip (3) from the frame. Reposition harness assemblies (2) out of the way.
Show/hide table
Illustration 3 g03691347 - Remove nuts (6) and washers (6) from both harness assemblies (7). Push harness assemblies (7) through bracket (4).
Show/hide table
Illustration 4 g03691519 - Remove cable strap (8) and reposition harness assembly (7) out of the way.
Show/hide table
Illustration 5 g03691550 - Disconnect harness assembly (9). Remove clamp (11). Disconnect cable assembly (10) and reposition cable assembly (10) out of the way.
Show/hide table
Illustration 6 g03691564 - Loosen clamp (12) in order to remove cable assembly (13) from the post.
Show/hide table
Illustration 7 g03691573 - Disconnect ground straps (13) and harness assembly (14).
Show/hide table
Illustration 8 g03691603 - Remove three bolts (15) and remove electronic starting motor (16).
Show/hide table
Illustration 9 g03691612 - Remove gasket (17).
- Install electric starting motor (16) in the reverse order of removal.
Caterpillar Information System:
Bench Test Procedure for Hydraulic Piston Pumps {5070} Bench Test Procedure for Hydraulic Piston Pumps {5070}
2014/07/29 New Resistance Temperature Sensors are Now Used in the Power Generator Group on Certain Off-Highway Trucks {1439, 4450}
14L Motor Grader Implement Electronic Control System General Information
AP1000F Asphalt Paver Machine Systems Solenoid Valve (Tow Point) - Remove and Install
966M XE and 972M XE Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Transmission - Accumulator Test
14L Motor Grader Implement Electronic Control System MID 082 - CID 1326 - FMI 02
AP655F and AP655F L Asphalt Paver Machine Systems Grade Control Mounting
14L Motor Grader Implement Electronic Control System MID 145 - CID 1326 - FMI 02
966M XE and 972M XE Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Position Sensor (Tilt Linkage) - Replace
966M XE and 972M XE Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Position Sensor (Lift Linkage) - Replace
420F2 IT, 420F2 ST, 427F2, 428F2, 430F2 IT, 430F2 ST, 432F2, 434F2 and 444F2 Backhoe Loaders Sensor Supply - Test
M318F, M320F and M322F Wheeled Excavators Hydraulic System Electronic Control (Return System)
Upshift / Downshift Push Button Switch Failures On The Left Hand Joystick Used On M Series and M Series 2 Motor Grader{5705, 7332} Upshift / Downshift Push Button Switch Failures On The Left Hand Joystick Used On M Series and M Series 2 Motor Grader{5705, 7332}
966M XE and 972M XE Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Pilot Pressure - Test and Adjust
2014/06/26 A New Seal Assembly for the Differential and Bevel Gear Group Is Now Used on Certain 797 Off-Highway Trucks {3256, 3258, 3281, 7555}
M318F, M320F and M322F Wheeled Excavators Hydraulic System Quick Coupler System
M318F, M320F and M322F Wheeled Excavators and MH3022 and MH3024 Material Handlers Stopping the Engine
M318F, M320F and M322F Wheeled Excavators Hydraulic System Grapple Rotate Hydraulic System
966M XE and 972M XE Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Hydraulic Oil Contamination - Test
R1700G Load Haul Dump Power Train Updrive Gears - Assemble
2014/06/23 Procedure to Rework the Machine Automation System Wiring Harness on Certain R3000H Load Haul Dump Machines {1408}
AP1000F Asphalt Paver Machine Systems Grade Control Mounting
AP1000F Asphalt Paver Machine Systems Control Valve (Auxiliary)
AP1000F Asphalt Paver Machine Systems Counterbalance Valve (Hopper Hoist, Tow Point)