Installation Of 3N4364 Core Assembly{1064}
Usage:
D379 (68B1064, (69B399-1262) D398 (66B1415, (67B590-1424) D399 (35B1, 91B405)
In place of former 1N5565 Core Assembly (1), a new 3N4364 Core Assembly (2) and 2N9839 Orifice (3) are given for service. When new core (2) is used along with a 6L4754 or 7L3222 Sea Water Pump or any other pump that will give an aftercooler circuit flow above 435 LPM (115 GPM), orifice (3) must be installed as shown. Do not install orifice (3) in any application where the aftercooler circuit flow is less than 435 LPM (115 GPM).
Caterpillar Information System:
Installing The 3N3166 Crankshaft Seal And 2W1794 Wear Sleeve{1160, 1161} Installing The 3N3166 Crankshaft Seal And 2W1794 Wear Sleeve{1160, 1161}
Installation Of A 2W6384 Or 2W6386 Time Delay Relay Conversion Group For Industrial, Marine And Generator Set Engines{1300, 1400, 1450} Installation Of A 2W6384 Or 2W6386 Time Delay Relay Conversion Group For Industrial, Marine And Generator Set Engines{1300, 1400, 1450}
Use Of 6V6124 Calibration Coil{0778, 0785} Use Of 6V6124 Calibration Coil{0778, 0785}
Installation Of Cylinder Head Assembly{1101} Installation Of Cylinder Head Assembly{1101}
Installation Of 3T9227 Wear Sleeve{3300} Installation Of 3T9227 Wear Sleeve{3300}
Using The 6V6000 Dial Bore Gauge Group{0761} Using The 6V6000 Dial Bore Gauge Group{0761}
Installation Of 6V4839 Cap And 15600 Snap Ring In 5P3508 Torque Multiplier{0614} Installation Of 6V4839 Cap And 15600 Snap Ring In 5P3508 Torque Multiplier{0614}
Installation Of 5N1948 And 2W3037 Sound Isolation Mounting Groups{1000, 3300, 7060} Installation Of 5N1948 And 2W3037 Sound Isolation Mounting Groups{1000, 3300, 7060}
Special Handling Information For Installation Of 2W1733 Or 2W1734 Crankshaft Seal Group{1160, 1161, 1202} Special Handling Information For Installation Of 2W1733 Or 2W1734 Crankshaft Seal Group{1160, 1161, 1202}
Installation Of Engine Block, Support Rails And/Or Oil Pan Base Assembly{1154, 1201, 1302} Installation Of Engine Block, Support Rails And/Or Oil Pan Base Assembly{1154, 1201, 1302}
Installation Of EMS (Electronic Monitoring System) Indicators{7450} Installation Of EMS (Electronic Monitoring System) Indicators{7450}
Use Of 6V4840 Tool Group To Install Water Ferrules{1201} Use Of 6V4840 Tool Group To Install Water Ferrules{1201}
Modification of Marine Transmission Lubrication System{3300} Modification of Marine Transmission Lubrication System{3300}
Installation Of Service Replacement Crankshaft For A 3304 Or 3306 Engine{1202} Installation Of Service Replacement Crankshaft For A 3304 Or 3306 Engine{1202}
Use Of 6V7028 Spring Seat Enlarger For 3200 Cylinder Heads{1101} Use Of 6V7028 Spring Seat Enlarger For 3200 Cylinder Heads{1101}
Operation, Maintenance, Troubleshooting And Repair Of 6V4135 Automatic Halogen Gas Leak Detector{0774} Operation, Maintenance, Troubleshooting And Repair Of 6V4135 Automatic Halogen Gas Leak Detector{0774}
Installation Of 1W4259 Valve Spring{1108} Installation Of 1W4259 Valve Spring{1108}
Installation Of 5N617 Enclosure Group For Package Generator Sets{7002} Installation Of 5N617 Enclosure Group For Package Generator Sets{7002}
Installation Of 3N5620 Spacer Group Or 3N5573 Spacer Assembly{3252} Installation Of 3N5620 Spacer Group Or 3N5573 Spacer Assembly{3252}
Procedure For Conversion From Oil Lubrication To Grease Lubrication For Rear Power Takeoff Clutches{3055} Procedure For Conversion From Oil Lubrication To Grease Lubrication For Rear Power Takeoff Clutches{3055}
Sea Trial Measurements On Caterpillar Marine Engines{1000, 3300} Sea Trial Measurements On Caterpillar Marine Engines{1000, 3300}
Installation Of 2W3815 Or 5N93 Inserts{1217} Installation Of 2W3815 Or 5N93 Inserts{1217}
Installation Of Altronic III Ignition Conversion Groups{1550, 1552, 1567} Installation Of Altronic III Ignition Conversion Groups{1550, 1552, 1567}
Use Of 6V7898 Dial Bore Gauge Group{0761} Use Of 6V7898 Dial Bore Gauge Group{0761}