Stick - 8.001 m (26.2500 ft)
Show/hide table
 | |
| Illustration 1 | g03346185 |
Show/hide table
| Specification for 395-9411 Stick | |||
| Item | Qty | Part | Specification Description |
| All bores must be free of paint. Coat all pin bores Including stick, upper frame, bushing, and cylinders with 5P-0960 Grease Cartridge. | |||
| Adjust to a total 1.6 mm (0.06 inch) maximum lateral clearance and a total 0.5 mm (0.02 inch) minimum lateral clearance for each boom cylinder eye. |
|||
| 1 | 2 | 395-8833 Bushing (1) | Before assembly, bore is 130.15 to 130.18 mm (5.124 to 5.125 inch). |
| After installation of bushing, check inside diameter and alignment of the bushing with 130.00 to 130.07 mm (5.118 to 5.121 inch) pin diameter. |
|||
| 2 | 1 | 395-8142 Pin As | Diameter is 130 mm (5.1 inch). |
| 3 | 1 | 395-8566 Nut | Hand tighten and then tighten to an additional turn of 90 ± 10 degrees. |
| 4 | 2 | 395-8834 Bushing (1) | Before assembly, bore is 120.14 to 120.18 mm (4.730 to 4.731 inch). |
| After installation of bushing, check inside diameter and alignment of the bushing with 119.99 to 120.07 mm (4.724 to 4.727 inch) pin diameter. |
|||
| 5 | As required, use the following shims to adjust the maximum lateral clearance to 0.8 mm (0.03 inch). |
||
| 8 | 395-8136 Shim | Thickness is 1.52 mm (0.060 inch). |
|
| 6 | 2 | 395-8138 Pin | Diameter is 119.924 to 120.000 mm (4.7214 to 4.7244 inch). |
| 7 | 2 | 395-8835 Bushing (1) | Before assembly, bore is 80.11 to 80.14 mm (3.154 to 3.155 inch). |
| After installation of bushing, check inside diameter and alignment of the bushing with 80.01 to 80.09 mm (3.150 to 3.153 inch) pin diameter. |
|||
Show/hide table
| ( 1 ) | Install the bushing in the bore so that the part number of the bushing is facing outward. |
Caterpillar Information System:
MH3049 Material Handler Machine System Upper Frame
MH3049 Material Handler Machine System Tire and Rim
R1600G Load Haul Dump Steering System Steering Time - Check - STIC Steering
R1600G Load Haul Dump Steering System Steering System Pressure - Test and Adjust
2013/05/06 Improved Barrel Now Used on the Tilt Cylinder on Certain R2900G Load Haul Dump Machines {5104}
Command for Underground General Information (Machine Automation System)
MH3049 Material Handler Air Conditioning and Heating Control
MH3049 Material Handler Machine Systems Pump Drive Group - Assemble
An Alternate Oil Filter Element for the Transmission Oil Filter Group Is Now Available for Certain Cat ® Machines {3004, 3067, 5056, 5068} An Alternate Oil Filter Element for the Transmission Oil Filter Group Is Now Available for Certain Cat ® Machines {3004, 3067, 5056, 5068}
2013/02/25 A New O-Ring Seal Is Now Used for the Wheel and Brake Group on Certain Large Off-Highway Trucks {4006, 4251, 7555}
2570C and 2670C Wheel Feller Bunchers Engine Air Filter Primary Element - Clean/Replace
C9.3 Engines for Caterpillar Built Machines Diesel Particulate Filter - Remove and Install
MH3049 Material Handler Machine System Steering Cylinder
C7.1 Engines for Caterpillar Built Machines Speed/Timing Sensor
C7.1 Engines for Caterpillar Built Machines Engine Oil Pump
MH3049 Material Handler Machine System Hydraulic Cylinder
MH3049 Material Handler Machine System Hydraulic Cylinder
C7.1 Engines for Caterpillar Built Machines Fuel Manifold (Rail)
C7.1 Engines for Caterpillar Built Machines Crankshaft Seals
C7.1 Engines for Caterpillar Built Machines Electronic Control Module
MH3049 Material Handler Machine System Counterweight and Mounting
C7.1 Engines for Caterpillar Built Machines Fuel Injection Pump
966M Tier 4, 966M Tier 4 Series XE, 972M Tier 4 and 972M Tier 4 Series XE Wheel Loaders Hydraulic Tank - Disassemble
C9.3 Engines for Caterpillar Built Machines DEF Injector and Mounting - Remove and Install