Steering System Pressure - Test and Adjust
STIC 转向
Show/hide table
所需工具     | ||
---|---|---|
零件号     | 零件描述     | 数量     |
177-7861     | 软管组件     | 1     |
6V-4143     | 连接器     | 2     |
8T-0859     | 压力表     | 1     |
Show/hide table
机器铰接或移动会导致人身伤亡。 机架移动可能砸伤人。 操作机器前,连接前部和后部机架之间的转向机架锁。 |
Show/hide table
高压喷射流体可造成人员伤亡。 高压喷射流体,即使是针孔大小的泄漏,也能穿透人体组织并造成严重的人员伤亡。 如果流体射入皮肤,必须立即寻求熟悉此类创伤的医生进行救治。 检查泄漏时,务必随身携带木板或硬纸板。 |
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
- 安装转向机架锁 (1) ,以便使机器无法转向。
Show/hide table
图 1 | g00942346 |
(1) 转向机架锁 |
- 从测压口 (2) 上拆下保护盖。 用 8T-0859 压力表 将软管组件连接至测压口 (2) 上。
Show/hide table
图 2 | g03346173 |
(2) 转向系统测压口 |
- 起动发动机。 高怠速运转发动机,将变速箱控制装置置于空档位置。
- 克服转向机架锁以使机器转向。
- 记录压力表上的压力。 压力表读数应为 18825 ± 345 kPa (2730 ± 50 psi)。
- 关停发动机。
- 如果压力读数符合技术规格,转至步骤 12。 如果压力读数不正确,转至步骤 8。
- 拆下塞 (3) 以接近转向系统压力调整螺钉。
Show/hide table
图 3 | g03346174 |
转向控制阀 (3) 塞 |
- 顺时针转动调整螺钉可升高压力。 逆时针转动调整螺钉可降低压力。
- 重复步骤 3 到步骤 7。
- 安装塞 (3) 。
- 从测压口拆下压力表。 将保护盖盖在测压口上。
- 拆下转向机架锁。
Caterpillar Information System:
2013/05/06 Improved Barrel Now Used on the Tilt Cylinder on Certain R2900G Load Haul Dump Machines {5104}
Command for Underground General Information (Machine Automation System)
MH3049 Material Handler Air Conditioning and Heating Control
MH3049 Material Handler Machine Systems Pump Drive Group - Assemble
An Alternate Oil Filter Element for the Transmission Oil Filter Group Is Now Available for Certain Cat ® Machines {3004, 3067, 5056, 5068} An Alternate Oil Filter Element for the Transmission Oil Filter Group Is Now Available for Certain Cat ® Machines {3004, 3067, 5056, 5068}
2013/02/25 A New O-Ring Seal Is Now Used for the Wheel and Brake Group on Certain Large Off-Highway Trucks {4006, 4251, 7555}
2570C and 2670C Wheel Feller Bunchers Engine Air Filter Primary Element - Clean/Replace
C9.3 Engines for Caterpillar Built Machines Diesel Particulate Filter - Remove and Install
2570C and 2670C Wheel Feller Bunchers Engine Starting with Auxiliary Start Receptacle - If Equipped
C7.1 Engines for Caterpillar Built Machines Piston and Rings
C9.3 Head Tool Improvements{0599, 0701, 0703, 1100} C9.3 Head Tool Improvements{0599, 0701, 0703, 1100}
MH3049 Material Handler Machine System Tire and Rim
R1600G Load Haul Dump Steering System Steering Time - Check - STIC Steering
MH3049 Material Handler Machine System Tire and Rim
MH3049 Material Handler Machine System Upper Frame
MH3049 Material Handler Machine System Stick - 8.001 m (26.2500 ft)
MH3049 Material Handler Machine System Steering Cylinder
C7.1 Engines for Caterpillar Built Machines Speed/Timing Sensor
C7.1 Engines for Caterpillar Built Machines Engine Oil Pump
MH3049 Material Handler Machine System Hydraulic Cylinder
MH3049 Material Handler Machine System Hydraulic Cylinder
C7.1 Engines for Caterpillar Built Machines Fuel Manifold (Rail)
C7.1 Engines for Caterpillar Built Machines Crankshaft Seals
C7.1 Engines for Caterpillar Built Machines Electronic Control Module