R1600H Load Haul Dump Power Train Caterpillar

Electronic Control Module (ECM) - Flash Program

Usage:

R1600H 9SD

Introduction

Perform the following procedure in order to flash program the Power Train Electronic Control Module (ECM). The ECM is flashed when a new ECM is fitted or when upgrading the software. The Caterpillar Electronic Technician (ET) contains the program WinFlash. WinFlash is used in order to load software into the ECM. The following procedure is used in order to flash software into the ECM.

Required Tools

Show/hide table

Table 1
Required Tools
Tool	Item	Qty	Part No	Description
E	E1	-	-	Caterpillar Electronic Technician (ET)
E	E2	1	171-4400	Communication Adapter

Show/hide table




Illustration 1	g01153429
Connections for the Communication Adapter II and the Caterpillar Electronic Technician (ET) The components that are needed to use the Communication Adapter II, and the Caterpillar ET to determine diagnostic codes are listed: (1) Current version of Caterpillar Electronic Technician software and an IBM-COMPATIBLE personal computer (2) 171-4400 Communication Adapter II (3) Special Publication, JEBD3003, Special Publication, JERD2124, Special Publication, JERD2129 Caterpillar Electronic Technician software

Procedure

Connect the Data Link Cable between Tooling (E2) and Tooling (E1) .

Connect the Data Link Cable between Tooling (E2) and the diagnostic connector of the machine.

Use WinFlash in order to load the software.

Caterpillar Information System:

WAVS Light Duty Installation Guide for Certain Cat® Products{7347, 7348} WAVS Light Duty Installation Guide for Certain Cat® Products{7347, 7348}

Failure of Temperature Sensor Gp in Clean Emissions Module on certain Cat® Products{108D, 1408, 1919} Failure of Temperature Sensor Gp in Clean Emissions Module on certain Cat® Products{108D, 1408, 1919}

12M Motor Grader Engine Supplement Engine - Remove and Install

12M Motor Grader Engine Supplement Flywheel Housing - Remove and Install

12M Motor Grader Engine Supplement Rear Gear Group - Remove and Install

12M Motor Grader Engine Supplement Flywheel and Rear Gear Group - Remove and Install - Drive Gear

MH3049 Material Handler C9 Engine Supplement Oil Pan - Remove and Install

563C and 573C Wheel Feller Bunchers Additional Messages

Software Installation Instructions of the Plus+1 Service Tool for Caterpillar P1STC Is Available for Caterpillar Paving Products {0785} Software Installation Instructions of the Plus+1 Service Tool for Caterpillar P1STC Is Available for Caterpillar Paving Products {0785}

2012/07/31 New Fluid Sampling Valve Is Now Used in the Hydraulic Oil Cooler Lines Group on 777G Off-Highway Trucks {1374, 5057}

12M Motor Grader Engine Supplement Rear Chassis Support - Remove and Install

2012/07/20 The Rod Assembly for the Platform Enclosure Group Has Been Updated on Certain Track-Type Tractors and Pipelayers {726A}

R1600H Load Haul Dump Power Train Electronic Control Module (ECM) - Replace

R1600H Load Haul Dump Power Train STIC Lockout Control - Check and Adjust

R1600H Load Haul Dump Power Train Limit Switch (STIC Lockout Control) - Check and Adjust

R1600H Load Haul Dump Power Train Speed Sensor - Adjust

R1600H Load Haul Dump Power Train Transmission Pressures - Test and Adjust

R1600H Load Haul Dump Power Train Output Transfer Gears - Adjust

R1600H Load Haul Dump Power Train NoSPIN Differential - Test

966M XE and 972M XE Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Transmission Pump

C7.1 Industrial Engine Exhaust Gas Valve (NRS)

C7.1 Industrial Engine Diesel Exhaust Fluid in Cold Weather

424B and 424B HD Backhoe Loaders Engine Supplement Fan - Remove and Install

C7.1 Industrial Engine Diesel Exhaust Fluid Filter - Replace