Conveyor Drive Chain (Auger) - Check and Adjust
注: 以下步骤描述用于检查和调整机器左侧螺旋布料器驱动链的步骤。 检查和调整牵引车右侧螺旋布料器驱动链的步骤相似。
Show/hide table
柴油发动机的排气含有可伤害人体的燃烧产物。 必须要在通风良好的地方起动发动机,如果在密闭的地方起动,就要把排气通到外面。 |
Show/hide table
旋转和运动的部件会造成人身伤害。 应避开所有旋转和运动的部件。 机器移动或发动机运转时决不能试图进行部件的调整工作,除非另有规定。 机器必须停在水平地面上,且发动机停止运转。 维修、修理或调整机器前,在起动开关和控制装置上要贴上"禁止操作"或类似的警告标签。 |
Show/hide table
机器突然动作,会导致人员伤亡。 机器突然移动,会对机上或机器近处的人员造成伤害。 为避免伤亡事故,开动机器之前,确保机器周围无人及没有各种障碍物。 |
- 把机器开到平整水平的路面。
- 将行驶操纵杆 (1) 移到 NEUTRAL(空档)位置。
Show/hide table
图 1 | g02598299 |
- 将转速旋钮 (4) 转到 MINIMUM(最小)位置。
- 将停车制动器开关 (2) 移到 ON(接通)位置。
- 将行驶模式开关 (3) 移到 PAVE(摊铺)位置。
- 将熨平板提升开关 (5) 移到 RAISE(上升)位置。 完全提升熨平板。
Show/hide table
图 2 | g02598301 |
- 接合机器两侧的熨平板锁止机构 (6) 。
Show/hide table
图 3 | g02598304 |
- 将熨平板提升开关 (5) 移到 FLOAT(浮动)位置。 将右仪表板上的熨平板提升开关移到 FLOAT(浮动)位置。
注: 两侧仪表板上的熨平板提升开关均必须处于 FLOAT(浮动)位置,才能降下熨平板。
- 熨平板落在熨平板锁机构上后,将熨平板提升开关 (5) 移到 HOLD(保持)位置。
- 将右熨平板伸出开关 (8) 移到 EXTEND(伸出)位置。 右熨平板扩展器完全伸出后,松开开关。
Show/hide table
图 4 | g02598307 |
- 将左熨平板伸出开关 (7) 移到 EXTEND(伸出)位置。 左熨平板扩展器完全伸出后,松开开关。
- 将油门控制开关 (9) 移到 LOW IDLE(低怠速)位置。 将开关保持在该位置少于 1 秒。
Show/hide table
图 5 | g02598308 |
- 发动机达到低怠速后,将发动机起动开关 (10) 移到 OFF(断开) 位置。
Show/hide table
图 6 | g02598310 |
- 用手前后旋转螺旋布料器 (11) 。
Show/hide table
图 7 | g02598311 |
- 测量螺旋布料器沿螺旋布料器板 (11) 运动的距离 (X) 。 测量结果应为 6.4 - 13 mm (0.25 - 0.5 in)。 如果测量值超出指定范围,采用以下步骤调整螺旋布料器驱动链张力。
- 松开但不要拆下四个安装螺栓 (12) 。
Show/hide table
图 8 | g02598312 |
- 松开锁紧螺母 (15) 。
Show/hide table
图 9 | g02598317 |
- 固定螺杆 (13) 的棱。 转动调整螺母 (14) ,直到螺旋布料器旋转在指定范围内。
- 拧紧锁紧螺母 (15) 。
- 拧紧安装螺栓 (12) 。
Caterpillar Information System:
PL83 and PL87 Pipelayers Power Train Track Roller - Remove and Install
C7.1 Engines for Caterpillar Built Machines Fuel Manifold (ARD) - Remove and Install - Pilot Solenoid Only
AP1000E and BG1000E Asphalt Pavers Machine Systems Piston Motor Case Drain Flow (Generator) - Test
PL83 and PL87 Pipelayers Power Train Sprocket Segment - Remove and Install
AP1000E and BG1000E Asphalt Pavers Machine Systems Fan Speed (Ventilation) - Test
2011/06/02 A New Direction and Speed Control Gp is now Available for Certain Vibratory Asphalt Compactors {5462}
C3.4B Industrial Engine Fan Clearance - Check
541 Series 2 Track Feller Buncher and 552 Series 2 Track Feller Buncher Machine Systems Leveling System
C27 Generator Set Fuel System Primary Filter (Water Separator) Element - Replace
C13, C15, and C18 Tier 4 Final Engines Engine Oil Pan
2013/09/12 A New Aftercooler Core Assembly is Now Used in the Air Aftercooler Group on the 773F and 775F Off-Highway Trucks {1063, 1353, 1806}
2011/07/08 A New Pump Control Valve Group is Now Used on the Piston Pump Groups on Certain Off-Highway Trucks {5070}
AP1000E and BG1000E Asphalt Pavers Machine Systems Conveyor Drive Chain (Drag) - Check and Adjust
AP1000E and BG1000E Asphalt Pavers Machine Systems Conveyor Chain (Drag) - Check and Adjust
AP1000E and BG1000E Asphalt Pavers Machine Systems Generator Frequency - Test and Adjust
AP1000E and BG1000E Asphalt Pavers Machine Systems Relief Valve (Charge) - Test and Adjust - Generator
PL83 and PL87 Pipelayers Power Train Front Track Roller Frame - Remove
C7.1 Engines for Caterpillar Built Machines Combustion Head - Remove and Install - Pilot Only System
AP1000E and BG1000E Asphalt Pavers Machine Systems Relief Valve (Main) - Test - Generator
PL83 and PL87 Pipelayers Power Train Front Track Roller Frame - Install
C7.1 Engines for Caterpillar Built Machines Nozzle Heater Harness - Remove and Install - Heated Nozzle Connection
AP1000E and BG1000E Asphalt Pavers Machine Systems Piston Pump Flow (Auxiliary) - Test
AP1000E and BG1000E Asphalt Pavers Machine Systems Relief Valve (Charge, Auger Conveyor and Drag Conveyor) - Test and Adjust
PL83 and PL87 Pipelayers Power Train Track Carrier Roller - Remove and Install - Right Side