Front Track Roller Frame - Remove
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 8B-7548     | 推拉器工具总成     | 1     |
5P-4808 | 盖     | 1     | |
9X-8883 | 螺栓     | 2     | |
8S-9089 | 螺栓     | 2     | |
5P-8245 | 硬垫圈     | 2     | |
5P-8247 | 硬垫圈     | 4     | |
B     | 1U-9200     | 操纵杆滚轮举倾机构     | 2     |
C     | 138-7575     | 连杆支架     | 2     |
开始:
- 分离履带。
注: 履带支重轮架没有机油排放塞。 使用真空泵。 如果真空泵不可用,当履带架从后履带支重轮架上拆下时将会进行排油。
- 将螺栓 (1) 、垫片、盖 (2) 和 O 形密封圈 (3) (未显示)从后履带支重轮架 (4) 上拆下。 对后履带支重轮架 (4) 的另一侧重复此步骤。
Show/hide table
图 1 | g01241945 |
- 使用工具 (A) ,将导向组件 (5) 从后履带支重轮架 (4) 的两侧拆下。
Show/hide table
图 2 | g01241946 |
- 连接适当的起吊设备,使其穿过前履带支重轮架 (6) 的两个环。 将工具 (C) 和适当的链条连接到前履带支重轮架 (6) 上。 将工具 (B) 连接到适当的链条上。 小心地将前履带支重轮架 (6) 移离后履带支重轮架 (4) 约 51 mm (2.0 in)。
Show/hide table
图 3 | g01352609 |
- 将适当的起吊设备和工具 (B) 连接到前履带支重轮架 (6) 的后面。 使用工具 (B) 保持前履带支重轮架 (6) 的高度。 前履带支重轮架 (6) 的重量约为 1565 kg (3450 lb)。 将前履带支重轮架 (6) 从后履带支重轮架 (4) 上拆下。
Show/hide table
图 4 | g01352615 |
Show/hide table
注意 |
---|
必须支撑前履带支重轮架 (6) 至从后履带支重轮架拆下前的水平。 以免损坏支重轮架。 工具 (B) 应与适当的起吊设备一起使用以便在看到导槽时尽快支撑前履带支重轮架。 |
- 必要时,拆下挡圈 (10) 、密封件 (9) 、挡圈 (8) 和轴承 (7) 。
Show/hide table
图 5 | g01241953 |
- 对机器另一侧上的前履带支重轮架重复步骤 1 至 5。
Caterpillar Information System:
AP1000E and BG1000E Asphalt Pavers Machine Systems Relief Valve (Charge) - Test and Adjust - Generator
AP1000E and BG1000E Asphalt Pavers Machine Systems Generator Frequency - Test and Adjust
AP1000E and BG1000E Asphalt Pavers Machine Systems Conveyor Chain (Drag) - Check and Adjust
AP1000E and BG1000E Asphalt Pavers Machine Systems Conveyor Drive Chain (Drag) - Check and Adjust
AP1000E and BG1000E Asphalt Pavers Machine Systems Conveyor Drive Chain (Auger) - Check and Adjust
PL83 and PL87 Pipelayers Power Train Track Roller - Remove and Install
C7.1 Engines for Caterpillar Built Machines Fuel Manifold (ARD) - Remove and Install - Pilot Solenoid Only
AP1000E and BG1000E Asphalt Pavers Machine Systems Piston Motor Case Drain Flow (Generator) - Test
PL83 and PL87 Pipelayers Power Train Sprocket Segment - Remove and Install
AP1000E and BG1000E Asphalt Pavers Machine Systems Fan Speed (Ventilation) - Test
2011/06/02 A New Direction and Speed Control Gp is now Available for Certain Vibratory Asphalt Compactors {5462}
C3.4B Industrial Engine Fan Clearance - Check
C7.1 Engines for Caterpillar Built Machines Combustion Head - Remove and Install - Pilot Only System
AP1000E and BG1000E Asphalt Pavers Machine Systems Relief Valve (Main) - Test - Generator
PL83 and PL87 Pipelayers Power Train Front Track Roller Frame - Install
C7.1 Engines for Caterpillar Built Machines Nozzle Heater Harness - Remove and Install - Heated Nozzle Connection
AP1000E and BG1000E Asphalt Pavers Machine Systems Piston Pump Flow (Auxiliary) - Test
AP1000E and BG1000E Asphalt Pavers Machine Systems Relief Valve (Charge, Auger Conveyor and Drag Conveyor) - Test and Adjust
PL83 and PL87 Pipelayers Power Train Track Carrier Roller - Remove and Install - Right Side
AP1000E and BG1000E Asphalt Pavers Machine Systems Relief Valve (Main, Auger Conveyor and Drag Conveyor) - Test and Adjust
PL83 and PL87 Pipelayers Power Train Track Carrier Roller - Remove and Install
PL83 and PL87 Pipelayers Power Train Track Adjuster - Remove and Install
PL83 and PL87 Pipelayers Power Train Track Adjuster - Disassemble
PL83 and PL87 Pipelayers Power Train Track Adjuster - Assemble