Relief Valve (Charge) - Test and Adjust - Generator
Show/hide table
柴油发动机的排气含有可伤害人体的燃烧产物。 必须要在通风良好的地方起动发动机,如果在密闭的地方起动,就要把排气通到外面。 |
Show/hide table
旋转和运动的部件会造成人身伤害。 应避开所有旋转和运动的部件。 机器移动或发动机运转时决不能试图进行部件的调整工作,除非另有规定。 机器必须停在水平地面上,且发动机停止运转。 维修、修理或调整机器前,在起动开关和控制装置上要贴上"禁止操作"或类似的警告标签。 |
Show/hide table
机器突然动作,会导致人员伤亡。 机器突然移动,会对机上或机器近处的人员造成伤害。 为避免伤亡事故,开动机器之前,确保机器周围无人及没有各种障碍物。 |
Show/hide table
滚热的油或液压油的压力会对人员造成伤害。 发动机停机之后,液压油的压力仍会保留在液压系统里。 对液压系统进行维修之前,如果不事先释放压力,可能会造成严重伤害。 确保所有的选装部件已降下,并确保在拆卸任何部件和管路前油冷却下来。 只能在发动机停机,并且加注口盖冷却到可以用徒手触摸时才能卸下加注口盖。 |
Show/hide table
注意 |
---|
机器做检查、保养、测试、调整和修理时,必须小心,不让液体流出。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关可提供予卡特彼勒机器的工具及适合于盛装液体的容器,请参阅技术手册, NENG2500, "卡特彼勒工具及车间用品指南"。 按照本地法规和指令处置所有液体。 |
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 说明     | 数量     |
A     | 8T-0855     | 压力表 0 到 4000 kPa (0 到 580 psi)     |
2     |
6V-4144 | 快速连接连接器     | 2     | |
B     | 177-7860     | 软管组件     | 2     |
6V-4142 | 接头     | 2     | |
6V-4143 | 快速连接连接器     | 2     |
Show/hide table
选装工具 (1)     | |||
---|---|---|---|
工具     | 零件号     | 说明     | 数量     |
C (2)     | 198-4234     | 数字指示器     | 1     |
E (2)     | 198-4236     | 适配器电缆组件     | 1     |
D     | 198-4237     | 压力传感器总成 0 - 3500 kPa (0 - 500 psi)     |
2     |
Show/hide table
( 1 ) | 可使用选装工具替换所需工具列表中的模拟压力表。 |
( 2 ) | 198-4234 数字指示器 和 198-4236 适配器电缆组件 是 198-4240 数字压力指示器总成 的一部分。 |
- 把机器开到平整水平的路面。
- 将行驶操纵杆 (1) 移到 NEUTRAL(空档)位置。
Show/hide table
图 1 | g02599557 |
- 将转速旋钮 (4) 转到 MINIMUM(最小)位置。
- 将停车制动器开关 (2) 移到 ON(接通)位置。
- 将行驶模式开关 (3) 移到 PAVE(摊铺)位置。
注: 要操作熨平板提升系统、料斗系统、斗门系统和螺旋布料器提升系统,机器必须处于 PAVE(摊铺)模式。
- 将熨平板提升开关 (5) 移到 FLOAT(浮动)位置。 使熨平板降到地面上。
注: 未激活操作台上的熨平板提升开关也必须处于 FLOAT(浮动)位置,才能降下熨平板。
Show/hide table
图 2 | g02599559 |
- 熨平板落在地面上后,将熨平板提升开关 (5) 移到 HOLD(保持)位置。
- 将油门控制开关 (6) 移到 LOW IDLE(低怠速)位置。 将开关保持在该位置少于 1 秒。
Show/hide table
图 3 | g02599561 |
- 将发动机起动开关 (7) 移到 OFF(断开)位置。
Show/hide table
图 4 | g02599562 |
- 打开机器右侧的检修面板 (8) 。
Show/hide table
图 5 | g02599563 |
- 将盖从发电机泵的端口 "G" 接头 (9) 上拆下。
Show/hide table
图 6 | g02599564 |
- 将工具 (B) 连接到接头 (9) 。
- 将盖从右行驶泵的端口 "L1" (10) 上拆下。
Show/hide table
图 7 | g02599565 |
- 将工具 (B) 连接到接头 (10) 。
- 将发动机起动开关 (7) 移到 START(起动)位置。 发动机起动后放开发动机起动开关钥匙。
- 将油门控制开关 (6) 移到 HIGH IDLE(高怠速)位置两次。 每次启动开关时,将开关保持在该位置少于 1 秒。 发动机转速应升至 2200 rpm。
- 监控操作员显示器上的液压油温度。 油温达到 43 ± 5.6 °C (110 ± 10 °F) 后停止运行机器。
Show/hide table
图 8 | g02599567 |
- 记录发电机泵端口 "G" (9) 上的压力。
- 记录右行驶泵端口 "L1" (10) 的壳体排油压力。
- 用步骤 18 中记录的压力值减去步骤 19 中记录的压力值。 压差应为 2550 ± 200 kPa (370 ± 29 psi)。
- 将油门控制开关 (6) 移到 LOW IDLE(低怠速)位置。 将开关保持在该位置少于 1 秒。
- 发动机达到低怠速后,将发动机起动开关 (7) 移到 OFF(断开) 位置。
- 如充油压力处于指定范围内,转到步骤 29。 如充油压力超出指定范围,转到步骤 24。
- 拆下增压安全阀 (11) 。
Show/hide table
图 9 | g02599569 |
- 将以下部件从泵壳体上拆下:
- 提升阀 (14)
- 垫片 (13)
- 弹簧 (12)
- 提升阀 (14)
Show/hide table
图 10 | g02599571 |
- 将垫片 (13) 添加到提升阀 (14) 以增加压力。 拆下垫片以减小压力。
注: 1 mm (0.04 in) 垫片将充油压力改变约 390 kPa (56.5 psi)。
- 将以下部件安装到泵壳体:
- 弹簧 (12)
- 垫片 (13)
- 提升阀 (14)
- 阀 (11)
- 弹簧 (12)
- 进行第 15 步。
- 拆下工具并更换接头 (8) 上的盖。 拆下工具并更换接头 (9) 上的盖。
- 关闭右检修面板 (8) 。
Caterpillar Information System:
AP1000E and BG1000E Asphalt Pavers Machine Systems Generator Frequency - Test and Adjust
AP1000E and BG1000E Asphalt Pavers Machine Systems Conveyor Chain (Drag) - Check and Adjust
AP1000E and BG1000E Asphalt Pavers Machine Systems Conveyor Drive Chain (Drag) - Check and Adjust
AP1000E and BG1000E Asphalt Pavers Machine Systems Conveyor Drive Chain (Auger) - Check and Adjust
PL83 and PL87 Pipelayers Power Train Track Roller - Remove and Install
C7.1 Engines for Caterpillar Built Machines Fuel Manifold (ARD) - Remove and Install - Pilot Solenoid Only
AP1000E and BG1000E Asphalt Pavers Machine Systems Piston Motor Case Drain Flow (Generator) - Test
PL83 and PL87 Pipelayers Power Train Sprocket Segment - Remove and Install
AP1000E and BG1000E Asphalt Pavers Machine Systems Fan Speed (Ventilation) - Test
2011/06/02 A New Direction and Speed Control Gp is now Available for Certain Vibratory Asphalt Compactors {5462}
C3.4B Industrial Engine Fan Clearance - Check
541 Series 2 Track Feller Buncher and 552 Series 2 Track Feller Buncher Machine Systems Leveling System
PL83 and PL87 Pipelayers Power Train Front Track Roller Frame - Remove
C7.1 Engines for Caterpillar Built Machines Combustion Head - Remove and Install - Pilot Only System
AP1000E and BG1000E Asphalt Pavers Machine Systems Relief Valve (Main) - Test - Generator
PL83 and PL87 Pipelayers Power Train Front Track Roller Frame - Install
C7.1 Engines for Caterpillar Built Machines Nozzle Heater Harness - Remove and Install - Heated Nozzle Connection
AP1000E and BG1000E Asphalt Pavers Machine Systems Piston Pump Flow (Auxiliary) - Test
AP1000E and BG1000E Asphalt Pavers Machine Systems Relief Valve (Charge, Auger Conveyor and Drag Conveyor) - Test and Adjust
PL83 and PL87 Pipelayers Power Train Track Carrier Roller - Remove and Install - Right Side
AP1000E and BG1000E Asphalt Pavers Machine Systems Relief Valve (Main, Auger Conveyor and Drag Conveyor) - Test and Adjust
PL83 and PL87 Pipelayers Power Train Track Carrier Roller - Remove and Install
PL83 and PL87 Pipelayers Power Train Track Adjuster - Remove and Install
PL83 and PL87 Pipelayers Power Train Track Adjuster - Disassemble