Conveyor Chain (Drag) - Check and Adjust
Show/hide table
柴油发动机的排气含有可伤害人体的燃烧产物。 必须要在通风良好的地方起动发动机,如果在密闭的地方起动,就要把排气通到外面。 |
Show/hide table
旋转和运动的部件会造成人身伤害。 应避开所有旋转和运动的部件。 机器移动或发动机运转时决不能试图进行部件的调整工作,除非另有规定。 机器必须停在水平地面上,且发动机停止运转。 维修、修理或调整机器前,在起动开关和控制装置上要贴上"禁止操作"或类似的警告标签。 |
Show/hide table
机器突然动作,会导致人员伤亡。 机器突然移动,会对机上或机器近处的人员造成伤害。 为避免伤亡事故,开动机器之前,确保机器周围无人及没有各种障碍物。 |
注: 机器配备两个拖拽输送机。 可在任一输送机上执行以下步骤。
- 把机器开到平整水平的路面。
- 将行驶操纵杆 (1) 移到 NEUTRAL(空档)位置。
Show/hide table
图 1 | g02623316 |
- 将转速旋钮 (4) 转到 MINIMUM(最小)位置。
- 将停车制动器开关 (2) 移到 ON(接通)位置。
- 将行驶模式开关 (3) 移到 PAVE(摊铺)位置。
注: 要操作熨平板提升系统、料斗系统、斗门系统和螺旋布料器提升系统,机器必须处于 PAVE(摊铺)模式。
- 将熨平板提升开关 (8) 移到 FLOAT(浮动)位置。 将右仪表板上的熨平板提升开关移到 FLOAT(浮动)位置。
注: 两侧仪表板上的熨平板提升开关均必须处于 FLOAT(浮动)位置,才能降下熨平板。
Show/hide table
图 2 | g02623317 |
- 熨平板落在地面上后,将熨平板提升开关 (8) 移到 HOLD(保持)位置。
- 将左料斗开关 (5) 移到 LOWER(下降)位置。 将右料斗开关 (6) 移到 LOWER(下降)位置。 完全降下料斗。
注: 如果机器处于双料斗模式,则任一料斗开关同时操作两个料斗。
- 对于配备自动斗门的机器,将斗门开关 (7) 移到 RAISE(提升)位置。 完全提升斗门。
- 对于未配备自动斗门的机器,手动提升斗门 (9) 。 使用斗门锁 (10) 将斗门锁止在完全提升位置。
Show/hide table
图 3 | g02623319 |
- 将油门控制开关 (11) 移到 LOW IDLE(低怠速)位置。 将开关保持在该位置少于 1 秒。
Show/hide table
图 4 | g02623322 |
- 发动机达到低怠速后,将发动机起动开关 (12) 移到 OFF(断开) 位置。
Show/hide table
图 5 | g02623323 |
- 在拖拽输送机底部,如果链条 (14) 的任何部位挂在主机架 (13) 的水平面下方,转到步骤 14。 如果不需要调整链条,转到步骤 17。
Show/hide table
图 6 | g02623326 |
- 将开口销 (15) 从调整连杆 (17) 上拆下。 将调整连杆从紧轴 (16) 和紧轴 (18) 上拆下。
Show/hide table
图 7 | g02623336 |
- 交替调整紧轴 (16) 和紧轴 (18) 直到拖拽输送机链条不再下垂。 使用调整连杆 (17) 逆时针转动紧轴,直到链条上紧。
注: 必须均匀拧紧紧轴 (16) 和紧轴 (18) 。
注: 链条张力正确时,链条底部任一点均与机器机架底部边缘齐平。
- 更换调整连杆 (17) 。 安装开口销 (15) 。
- 降下斗门。.
Caterpillar Information System:
AP1000E and BG1000E Asphalt Pavers Machine Systems Conveyor Drive Chain (Drag) - Check and Adjust
AP1000E and BG1000E Asphalt Pavers Machine Systems Conveyor Drive Chain (Auger) - Check and Adjust
PL83 and PL87 Pipelayers Power Train Track Roller - Remove and Install
C7.1 Engines for Caterpillar Built Machines Fuel Manifold (ARD) - Remove and Install - Pilot Solenoid Only
AP1000E and BG1000E Asphalt Pavers Machine Systems Piston Motor Case Drain Flow (Generator) - Test
PL83 and PL87 Pipelayers Power Train Sprocket Segment - Remove and Install
AP1000E and BG1000E Asphalt Pavers Machine Systems Fan Speed (Ventilation) - Test
2011/06/02 A New Direction and Speed Control Gp is now Available for Certain Vibratory Asphalt Compactors {5462}
C3.4B Industrial Engine Fan Clearance - Check
541 Series 2 Track Feller Buncher and 552 Series 2 Track Feller Buncher Machine Systems Leveling System
C27 Generator Set Fuel System Primary Filter (Water Separator) Element - Replace
C13, C15, and C18 Tier 4 Final Engines Engine Oil Pan
AP1000E and BG1000E Asphalt Pavers Machine Systems Generator Frequency - Test and Adjust
AP1000E and BG1000E Asphalt Pavers Machine Systems Relief Valve (Charge) - Test and Adjust - Generator
PL83 and PL87 Pipelayers Power Train Front Track Roller Frame - Remove
C7.1 Engines for Caterpillar Built Machines Combustion Head - Remove and Install - Pilot Only System
AP1000E and BG1000E Asphalt Pavers Machine Systems Relief Valve (Main) - Test - Generator
PL83 and PL87 Pipelayers Power Train Front Track Roller Frame - Install
C7.1 Engines for Caterpillar Built Machines Nozzle Heater Harness - Remove and Install - Heated Nozzle Connection
AP1000E and BG1000E Asphalt Pavers Machine Systems Piston Pump Flow (Auxiliary) - Test
AP1000E and BG1000E Asphalt Pavers Machine Systems Relief Valve (Charge, Auger Conveyor and Drag Conveyor) - Test and Adjust
PL83 and PL87 Pipelayers Power Train Track Carrier Roller - Remove and Install - Right Side
AP1000E and BG1000E Asphalt Pavers Machine Systems Relief Valve (Main, Auger Conveyor and Drag Conveyor) - Test and Adjust
PL83 and PL87 Pipelayers Power Train Track Carrier Roller - Remove and Install