Bucket Positioner Control - Remove and Install
Removal Procedure
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 1P-1855 | Retaining Ring Pliers | 1 |
- Remove bolts (1) and plate assembly (2) .
Show/hide table
 | |
| Illustration 1 | g01247246 |
- Use Tooling (A) in order to remove retaining ring (4). Remove tube assembly (3) .
Show/hide table
 | |
| Illustration 2 | g01247247 |
- Remove bolts (6) in order to reposition bracket assembly (5) (not shown).
Show/hide table
 | |
| Illustration 3 | g01523982 |
Show/hide table
 | |
| Illustration 4 | g01523987 |
- Loosen nut (9). Disconnect harness assemblies (7) from roller switch assembly (8). Remove roller switch assembly (8) from bracket assembly (5) .
Installation Procedure
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 1P-1855 | Retaining Ring Pliers | 1 |
- Install roller switch assembly (8) into bracket assembly (5). Connect harness assemblies (7). Tighten nut (9) to a torque of 19 ± 2 N·m (14 ± 1 lb ft).
Show/hide table
| | |
| Illustration 5 | g01523987 |
- Position bracket assembly (5) (not shown). Install bolts (6) .
Show/hide table
| | |
| Illustration 6 | g01523982 |
- Install tube assembly (3). Use Tooling (A) in order to install retaining ring (4) .
Show/hide table
| | |
| Illustration 7 | g01247247 |
- Install plate assembly (2) and bolts (1) .
Show/hide table
| | |
| Illustration 8 | g01247246 |
- Adjust the bucket positioner control. Refer to Specifications, "Bucket Positioner and Lift Kickout".
Caterpillar Information System:
PL61 Pipelayer Machine Systems Shutoff Valve (Implement Lockout)
PL61 Pipelayer Machine Systems Load Control Valve (Dead Engine Lower)
2008/06/16 Correction to Operation and Maintenance Manual , "Braking System - Test" {4250, 4251, 4267}
2008/07/07 Correction to Systems Operation Testing and Adjusting , "Sequence Valve (Brake Release)" {4282}
R2900G Load Haul Dump Braking System Sequence Valve (Brake Release)
2008/07/07 Correction to Systems Operation Testing and Adjusting , "Service and Parking Brake System" {4251, 4267}
2008/07/07 Correction to Systems Operation Testing and Adjusting , "Brake Release System" {4250, 4284}
2008/07/07 Correction to Systems Operation Testing and Adjusting , "Brake Control Valve (Parking)" {4282}
2008/05/05 New Software for the Caterpillar Monitoring System is Now Available {7490, 7620}
416E, 420E and 430E Backhoe Loaders Machine Systems Bucket - Remove and Install
793F and 793F CMD Off-Highway Truck Hydraulic System Hoist Cylinder
414E, 416E, 420E and 430E Backhoe Loaders Machine Systems Tilt Cylinder - Remove and Install
795F AC Off-Highway Truck Air System Check Valve (Air Tank)
C27 and C32 Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install - Type 2
Filtration Procedure for Pipelayer Hydraulic Oil Equipped with Ecology Drain Valve {0680, 0768, 5050, 5056} Filtration Procedure for Pipelayer Hydraulic Oil Equipped with Ecology Drain Valve {0680, 0768, 5050, 5056}
2008/05/19 Improved Procedure to Install Double Wall Fuel Lines {1252, 1254}
3516B Engine for 994F and 994H Wheel Loaders Timing - Calibrate
416E, 420E and 430E Backhoe Loaders Engine Supplement Radiator, Refrigerant Condenser, and Hydraulic and XMSN Oil Cooler - Remove
795F AC and 795F AC XQ Off-Highway Truck Steering System Accumulator (Steering) - Test and Charge
793F and 793F CMD Off-Highway Truck Air System Air Starting Motor
3512C Engine and 785D Off-Highway Truck/Tractors ECM Software - Install
2008/07/07 A New Pinion Assembly Updates the Differential Group {3258}
Failures at Early Hours of the Hoses in the Transmission Oil Cooler Group on Specific Off-Highway Trucks{1375} Failures at Early Hours of the Hoses in the Transmission Oil Cooler Group on Specific Off-Highway Trucks{1375}
793F and 793F CMD Off-Highway Truck Air System Relay Valve (Air Start)