Speed and Vibratory Module Group - Canopy
Show/hide table
Illustration 1 | g01409843 |
(1) Torque for two bolts ...
(2) Apply adhesive sideways on bottom side of plate to seal with cover.
Speed Sensor
Note: The following is a procedure for installing the speed sensor.
- Run the machine without the speed sensor (3) until one of the four corners of the square nut faces the hole for the sensor.
- Apply 5P-3413 Pipe Sealant to the threads of the speed sensor (3).
- Screw the speed sensor (3) until the sensor touches the square nut. Unscrew approximately one turn.
- Gap between the speed sensor (3) and the shaft
1.5 ± 0.5 mm (0.06 ± 0.02 inch) - The nut that secures the speed sensor (3) should be torqued to
15 ± 1 N·m (11 ± 1 lb ft) .
Caterpillar Information System:
2007/08/27 Precautions for Cylinder Liner Installation {1201, 1216}
3176C Engine for the R1600G and the R1700G Load Haul Dumps Timing - Calibrate
797 Rear Wheel Bearing Full Single Life Reusability Guidelines {4201} 797 Rear Wheel Bearing Full Single Life Reusability Guidelines {4201}
14M Motor Grader Safety Messages
938H Wheel Loader and IT38H Integrated Toolcarrier Hydraulic System Relief Valve (Signal) - Test and Adjust
CP76 and CS76 Vibratory Compactors Propel System Relief Valve (Main, Axle Propel Pump) - Test and Adjust
CP54 and CS54 Vibratory Soil Compactors Machine Systems Speedometer
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train Piston Motor (Hydrostatic) - Assemble
Installing the 290-9911 Engine Enclosure Seal Kit {7263, 7263, 7273} Installing the 290-9911 Engine Enclosure Seal Kit {7263, 7263, 7273}
3176C Engine for the R1600G and the R1700G Load Haul Dumps Sensor Supply - Test
140M Motor Grader Engine Supplement Fuel Filter (Secondary) and Fuel Filter Base - Remove and Install
CP54 and CS54 Vibratory Soil Compactors Machine Systems Operator Compartment
Adjustment Procedure for the Extendable Stick Wear Pads{6533} Adjustment Procedure for the Extendable Stick Wear Pads{6533}
Bench Test Procedure For A 784B, 784C, 785B, 785C, and 785D Off-Highway Truck Torque Converter{3101} Bench Test Procedure For A 784B, 784C, 785B, 785C, and 785D Off-Highway Truck Torque Converter{3101}
140M Motor Grader Engine Supplement Fuel Priming Pump and Water Separator - Remove and Install
924H, 924HZ, 928HZ and 930H Wheel Loaders MID 081 - CID 1960 - FMI 09
Reuse and Salvage for Turbochargers {0760, 0767, 1052} Reuse and Salvage for Turbochargers {0760, 0767, 1052}
R1600G Load Haul Dump Engine and Machine Warm-Up
R1600G Load Haul Dump Parking Brake Manual Release
140H and 160H Motor Graders Maintenance Interval Schedule
CP54 and CS54 Vibratory Soil Compactors Machine Systems Speed and Vibratory Module Group - Cab
140M Motor Grader Engine Supplement Aftercooler - Remove
14M Motor Grader Operator Controls
2007/08/27 Precautions for Cylinder Liner Installation {1201, 1216}