Speedometer
Show/hide table
Illustration 1 | g01409761 |
(1) Torque for three bolts that secures the bracket that supports the speedometer ... 6 ± 1 N·m (53 ± 9 lb in)
Speed Sensor
Note: The following is a procedure for installing the speed sensor.
- Run the machine without the speed sensor (2) until one of the four corners of the square nut faces the hole for the sensor.
- Apply 5P-3413 Pipe Sealant to the threads of the speed sensor (2) .
- Screw the speed sensor (2) until the sensor touches the square nut. Unscrew approximately one turn.
- Gap between the speed sensor (2) and the shaft 1.5 ± 0.5 mm (0.06 ± 0.02 inch)
- The nut that secures the speed sensor (2) should be torqued to 16 ± 1 N·m (140 ± 10 lb in).
Caterpillar Information System:
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train Piston Motor (Hydrostatic) - Assemble
Installing the 290-9911 Engine Enclosure Seal Kit {7263, 7263, 7273} Installing the 290-9911 Engine Enclosure Seal Kit {7263, 7263, 7273}
3176C Engine for the R1600G and the R1700G Load Haul Dumps Sensor Supply - Test
140M Motor Grader Engine Supplement Fuel Filter (Secondary) and Fuel Filter Base - Remove and Install
CP54 and CS54 Vibratory Soil Compactors Machine Systems Operator Compartment
16M Motor Grader Operator Controls
Information Is Not Provided in Specifications, RENR4895 for B2 Series Skid Steer Loaders{5050, 7000} Information Is Not Provided in Specifications, RENR4895 for B2 Series Skid Steer Loaders{5050, 7000}
C4.4 (Mech) Industrial Engine Fuel System Pressure - Test
3176C Engine for the R1600G and the R1700G Load Haul Dumps Sensor Signal (Analog, Active) - Test
3524B and C175 Engines for Off-Highway Truck/Tractors Turbocharger
Wiring the 9X-9591 Electrical Converter Gp (PULSE WIDTH MODULATED){1421, 1901, 7490} Wiring the 9X-9591 Electrical Converter Gp (PULSE WIDTH MODULATED){1421, 1901, 7490}
770 and 772 Off-Highway Trucks Power Train Transmission Hydraulic Control - Assemble
CP76 and CS76 Vibratory Compactors Propel System Relief Valve (Main, Axle Propel Pump) - Test and Adjust
938H Wheel Loader and IT38H Integrated Toolcarrier Hydraulic System Relief Valve (Signal) - Test and Adjust
14M Motor Grader Safety Messages
797 Rear Wheel Bearing Full Single Life Reusability Guidelines {4201} 797 Rear Wheel Bearing Full Single Life Reusability Guidelines {4201}
3176C Engine for the R1600G and the R1700G Load Haul Dumps Timing - Calibrate
2007/08/27 Precautions for Cylinder Liner Installation {1201, 1216}
CP54 and CS54 Vibratory Soil Compactors Machine Systems Speed and Vibratory Module Group - Canopy
Adjustment Procedure for the Extendable Stick Wear Pads{6533} Adjustment Procedure for the Extendable Stick Wear Pads{6533}
Bench Test Procedure For A 784B, 784C, 785B, 785C, and 785D Off-Highway Truck Torque Converter{3101} Bench Test Procedure For A 784B, 784C, 785B, 785C, and 785D Off-Highway Truck Torque Converter{3101}
140M Motor Grader Engine Supplement Fuel Priming Pump and Water Separator - Remove and Install
924H, 924HZ, 928HZ and 930H Wheel Loaders MID 081 - CID 1960 - FMI 09
Reuse and Salvage for Turbochargers {0760, 0767, 1052} Reuse and Salvage for Turbochargers {0760, 0767, 1052}