Wheel Lean Arm and Axle Bushings - Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 5P-2145 | Bearing Puller Adapter | 1 |
6V-3160 | Double Acting Cylinder | 1 | |
9U-6833 | Nut | 1 | |
4C-9633 | Puller Stud | 1 | |
5P-8250 | Washer | 1 | |
3S-6224 | Electric Hydraulic Pump Gp | 1 | |
B | 1P-0510 | Driver Gp | 1 |
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- Lower the temperature of bearing (12).
- Use Tooling (B) in order to install bearing (12) into axle (10).
- Install lip seal (11).
Show/hide table
Illustration 2 g01408145 - Use Tooling (A) in order to install bearings (9) into wheel lean arm (6).
Show/hide table
Illustration 3 g01408084 - Attach a suitable lifting device to wheel lean arm (6). The weight of wheel lean arm (6) is approximately
91 kg (200 lb) . - Position wheel lean arm (6) and install pin (8).
- Install bolt (7).
Show/hide table
Illustration 4 g01408571 - Position wheel lean cylinder (1) and install pin (5).
- Remove the suitable lifting device from wheel lean arm (6).
Show/hide table
Illustration 5 g01408013 - Attach a suitable lifting device to wheel lean bar (2). The weight of wheel lean bar (2) is approximately
55 kg (122 lb) . - Position wheel lean bar (2).
- Install bolt (4) and retainer (3) in order to secure pin (5). Repeat this step for the opposite side of pin (5).
- Remove the suitable blocking from wheel lean cylinder (1).
Show/hide table
Illustration 1 | g01408547 |
End By:
- Install the wheel drive. Refer to Disassembly and Assembly, "Wheel Drive - Install".
Caterpillar Information System:
450E Backhoe Loader Tire Inflation with Air
CP54 and CS54 Vibratory Soil Compactors Machine Systems Flood Lighting
2007/09/10 Improved Seals in the Suspension Cylinders Are Now Used {7201}
Procedure to Correct Straight Line Travel{5057} Procedure to Correct Straight Line Travel{5057}
New Retaining Method Is Available for the Front Axle Mounting Pin and the Rear Axle Mounting Pin{3013} New Retaining Method Is Available for the Front Axle Mounting Pin and the Rear Axle Mounting Pin{3013}
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Soil Compactors Machine Systems Cab Liner
CP76 and CS76 Vibratory Compactors Machine Systems Piston Motor (Vibratory)
CP76 and CS76 Vibratory Compactors Machine Systems Magnetic Sensor (Vibratory) - Test and Adjust
CP76 and CS76 Vibratory Compactors Machine Systems Fan Motor Speed (Radiator Cooling) - Test and Adjust
140M Motor Grader Engine Supplement Vibration Damper - Remove and Install
Installation of the Power Shift Solenoid{5264, 5479} Installation of the Power Shift Solenoid{5264, 5479}
CP76 and CS76 Vibratory Compactors Machine Systems Vibratory Frequency - Test and Adjust
Procedure to Provide Pinion Bearings with Sufficient Oil {3256, 3258} Procedure to Provide Pinion Bearings with Sufficient Oil {3256, 3258}
CP54 and CS54 Vibratory Soil Compactors Machine Systems Heater Lines
CP76 and CS76 Vibratory Compactors Machine Systems Gear Pump Flow (Steering) - Test
CP76 and CS76 Vibratory Compactors Machine Systems Relief Valve (Main, Vibratory) - Test and Adjust
140M Motor Grader Engine Supplement Radiator - Remove
3176C Engine for the R1600G and the R1700G Load Haul Dumps Electrical Power Supply - Test
CP54 and CS54 Vibratory Soil Compactors Machine Systems Air Lines
3176C Engine for the R1600G and the R1700G Load Haul Dumps Speed Control (Switch) - Test
CP76 and CS76 Vibratory Compactors Machine Systems Piston Pump Neutral (Vibratory) - Test and Adjust
Rework Procedure For the 192-0086 Ride Control Valve Gp {5004, 5054} Rework Procedure For the 192-0086 Ride Control Valve Gp {5004, 5054}
CS54 and CP54 Vibratory Soil Compactors Operator Controls
CP76 and CS76 Vibratory Compactors Machine Systems Piston Pump (Vibratory)